- 您現在的位置：買賣IC網 > PDF目錄97865 > DS1963L-F5 (DALLAS SEMICONDUCTOR) SPECIALTY MEMORY CIRCUIT, MEDB2 PDF資料下載
參數資料
| 型號： | DS1963L-F5 |
| 廠商： | DALLAS SEMICONDUCTOR |
| 元件分類： | Memory IC:Other |
| 英文描述： | SPECIALTY MEMORY CIRCUIT, MEDB2 |
| 封裝： | MICROCAN-2 |
| 文件頁數： | 21/24頁 |
| 文件大?。?/td> | 482K |
| 代理商： | DS1963L-F5 |
DS1963L
6 of 24
MEMORY FUNCTION COMMANDS
The “Memory Function Flow Chart” (Figure 7) describes the protocols necessary for accessing the
memory. An example follows the flowchart. The communication between master and DS1963L takes
place either at regular speed (default, OD = 0) or at Overdrive speed (OD = 1). If not explicitly set into
the Overdrive mode the DS1963L assumes regular speed.
Write Scratchpad Command [0FH]
After issuing the write scratchpad command, the master must first provide the 2-byte target address,
followed by the data to be written to the scratchpad. The data will be written to the scratchpad starting at
the byte offset (T4:T0). The ending offset (E4: E0) will be the byte offset at which the master stops
writing data. Only full data bytes are accepted. If the last data byte is incomplete its content will be
ignored and the partial byte flag PF will be set.
When executing the Write Scratchpad command the CRC generator inside the DS1963L (see Figure 12)
calculates a CRC over the entire data stream, starting at the command code and ending at the last data
byte sent by the master. This CRC is generated using the CRC16 polynomial by first clearing the CRC
generator and then shifting in the command code (0FH) of the Write Scratchpad command, the Target
Addresses TA1 and TA2 as supplied by the master and all the data bytes. The master may end the Write
Scratchpad command at any time. However, if the ending offset is 11111b, the master may send 16 read
time slots and will receive the CRC generated by the DS1963L.
The memory address range of the DS1963L is 0000H to 01FFH. If the bus master sends a target address
higher than this, the internal circuitry of the chip will set the seven most significant address bits to 0 as
they are shifted into the internal address register. The Read Scratchpad command will reveal the target
address as it will be used by the DS1963L. The master will identify such address modifications by
comparing the target address read back to the target address transmitted. If the master does not read the
scratchpad, a subsequent copy scratchpad command will not work since the most significant bits of the
target address the master sends will not match the value the DS1963L expects.
Read Scratchpad Command [AAH]
This command is used to verify scratchpad data and target address. After issuing the read scratchpad
command, the master begins reading. The first 2 bytes will be the target address. The next byte will be the
ending offset/data status byte (E/S) followed by the scratchpad data beginning at the byte offset (T4: T0).
The master may read data until the end of the scratchpad after which the data read will be all logic 1’s.
Copy Scratchpad [5AH]
This command is used to copy data from the scratchpad to memory. After issuing the copy scratchpad
command, the master must provide a 3-byte authorization pattern which can be obtained by reading the
scratchpad for verification. This pattern must exactly match the data contained in the three address
registers (TA1, TA2, E/S, in that order). If the pattern matches, the AA (Authorization Accepted) flag
will be set and the copy will begin. A pattern of alternating 1s and 0s will be transmitted after the data has
been copied until a reset pulse is issued by the master. Any attempt to reset the part will be ignored while
the copy is in progress. Copy typically takes 30
s.
The data to be copied is determined by the three address registers. The scratchpad data from the
beginning offset through the ending offset, will be copied to memory, starting at the target address.
Anywhere from 1 to 32 bytes may be copied to memory with this command. The AA flag will be cleared
only by executing a write scratchpad command.
相關PDF資料 |
PDF描述 |
|---|---|
| DS1963S | SPECIALTY MEMORY CIRCUIT, MEDB2 |
| DS1985-F3 | 2K X 8 EEPROM 3V, RDB2 |
| DS1986-F3 | 64K X 1 OTPROM, MEDB2 |
| DS1986-F5 | 64K X 1 OTPROM, MADB2 |
| DS1991L-F5 | SPECIALTY MEMORY CIRCUIT, MEDB2 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1963L-F5+ | 功能描述:iButton RoHS:否 存儲類型:SRAM 存儲容量:512 B 組織: 工作電源電壓:3 V to 5.25 V 接口類型:1-Wire 最大工作溫度:+ 85 C 尺寸:17.35 mm x 5.89 mm 封裝 / 箱體:F5 MicroCan 制造商:Maxim Integrated |
| DS1963L-F5+W | 功能描述:iButton RoHS:否 存儲類型:SRAM 存儲容量:512 B 組織: 工作電源電壓:3 V to 5.25 V 接口類型:1-Wire 最大工作溫度:+ 85 C 尺寸:17.35 mm x 5.89 mm 封裝 / 箱體:F5 MicroCan 制造商:Maxim Integrated |
| DS1963R-F5+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| DS1963S | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:SHA iButton |
| DS1963S+F5 | 制造商:Maxim Integrated Products 功能描述:SHA IBTN 8SOIC - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。