BEN should be equal to VCC
參數資料
型號： DS1875T+
廠商： Maxim Integrated Products
文件頁數： 9/92頁
文件大?。?/td> 0K
描述： IC SFP CTRLR/TRIPLEXER 38-TQFN
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 90
應用： 光纖
接口： I²C
電源電壓： 2.85 V ~ 3.9 V
封裝/外殼： 38-WFQFN 裸露焊盤
供應商設備封裝： 38-TQFN（5x7）
包裝： 管件
安裝類型： 表面貼裝
產品目錄頁面： 1431 (CN2011-ZH PDF)
DS1875
DC Operation
When using autodetect mode or closed-loop mode,
BEN should be equal to VCC or long burst. In open-loop
mode, BEN should be ground or any burst length.
Modulation Control
The MOD output is an 8-bit scaleable voltage output
that interfaces with the MAX3643’s VMSET input. An
external resistor to ground from the MAX3643’s
MODSET pin sets the maximum current that the voltage
at the VMSET input can produce for a given output
range. This resistor value should be chosen to produce
the maximum modulation current the laser type requires
over temperature. Then the MOD output’s scaling is
used to calibrate the full-scale (FS) modulation output
to a particular laser’s requirements. This allows the
application to take full advantage of the MOD output’s
resolution. The modulation LUT can be programmed in
2°C increments over the -40°C to +102°C range.
Ranging of the MOD DAC is possible by programming
a single byte in Table 02h, Register 8Bh.
BIAS and MOD Output During Power-Up
On power-up the modulation and bias outputs remain off
until VCC is above VPOA, a temperature conversion has
been completed, and, if the VCC ADC alarm is enabled,
a VCC conversion above the customer-defined VCC low
alarm level must clear the VCC low alarm (tINIT). Once all
these conditions (tINIT) are satisfied, the MOD output is
enabled with the value determined by the temperature
conversion and the modulation LUT (Table 04h).
When the MOD output is enabled, the BIAS output is
turned on to a value equal to the temperature-indexed
value in the BIAS LUT (Table 08h). Next, the APC inte-
grator is enabled, and single LSB steps are taken to
tightly control the average power.
If a fault is detected and TX-D is toggled to re-enable
the outputs, the DS1875 powers up following a similar
sequence to an initial power-up. The only difference is
that the DS1875 already determined the present tem-
perature, so the tINIT time is not required for the
DS1875 to recall the APC and MOD set points from
EEPROM.
12
3
4
56
7
89
10
11
12
13
tINIT
VPOA
VMOD
IBIAS
VCC
BIAS
SAMPLE
APC INTEGRATOR ON
BIAS LUT
VALUE
Figure 1. Power-Up Timing (BEN is a Long Burst)
PON Triplexer and SFP Controller
______________________________________________________________________________________
17
相關PDF資料
PDF描述
D38999/20MD18PA CONN RCPT 18POS WALL MNT W/PINS
MAX7359ETG+ IC KEY SWITCH 2WIRE 24-TQFN
USB-232-SS IC USB ASYNC SRL UART 20-SSOP
MS27473E24F61P CONN PLUG 61POS STRAIGHT W/PINS
MS27474E10F98PA CONN RCPT 6POS JAM NUT W/PINS
相關代理商/技術參數
參數描述
DS1875T+ 功能描述:ADC / DAC多通道 PON Triplexer & SFP Controller RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40
DS1875T+T&R 制造商:Maxim Integrated Products 功能描述:PON TRIPLEXER 38TQFN EP - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC SFP CTRLR/TRIPLEXER 38-TQFN 制造商:Maxim Integrated Products 功能描述:ADC / DAC Multichannel PON Triplexer & SFP Controller
DS1875T+T&R 功能描述:ADC / DAC多通道 PON Triplexer & SFP Controller RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40
DS1875T+TR 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:PON Triplexer and SFP Controller
DS1876 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:SFP Controller with Dual LDD Interface
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*