參數資料
型號： DS1875T+
廠商： Maxim Integrated Products
文件頁數： 63/92頁
文件大?。?/td> 0K
描述： IC SFP CTRLR/TRIPLEXER 38-TQFN
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 90
應用： 光纖
接口： I²C
電源電壓： 2.85 V ~ 3.9 V
封裝/外殼： 38-WFQFN 裸露焊盤
供應商設備封裝： 38-TQFN（5x7）
包裝： 管件
安裝類型： 表面貼裝
產品目錄頁面： 1431 (CN2011-ZH PDF)
DS1875
PON Triplexer and SFP Controller
66
______________________________________________________________________________________
Table 02h, Register 89h: CONFIG
FACTORY DEFAULT
00h
READ ACCESS
PW2
WRITE ACCESS
PW2
MEMORY TYPE
Nonvolatile (SEE)
89h
FETG DIR
TX-F LEN
M3QT LEN
ASEL
BOLFS
RSSI_FC
RSSI_FF
EN5TO8B
BIT 7
BIT 0
Configure the memory location and the polarity of the digital outputs.
BIT 7
FETG DIR: Chooses the direction or polarity of the FETG output for normal operation.
0 = (Default) Under normal operation, FETG is pulled low.
1 = Under normal operation, FETG is pulled high.
BIT 6
TX-F LEN: The TX-F output pin always reflects the wired-OR of all TX-F enabled alarm states. This
bit enables the latching of the alarm state for the TX-F output pin.
0 = (Default) Not latched.
1 = The alarm bits are latched until cleared by a TX-D transition or power-down. If the VCC alarm is
enabled for either FETG or TX-F, then latching is disabled until after the first VCC measurement is
made above the VCC ALARM LO set point to allow for proper operation during slow power-on
cycles.
BIT 5
M3QT LEN: This bit enables the latching of the alarm for the M3QT.
0 = (Default) Not latched.
1 = The alarm bit is latched until cleared by setting the M3QT RESET bit (Byte 78h).
BIT 4
ASEL: Address select.
0 = (Default) Device address of A2h.
1 = Device address is equal to the value found in the DEVICE ADDRESS byte (Table 02h, 8Ch).
BIT 3
BOLFS: Bias open-loop full scale.
0 = (Default) Full scale is 600μA.
1 = Full scale is 1.2mA.
BITS 2:1
RSSI_FC and RSSI_FF: RSSI force coarse and RSSI force fine. Control bits for RSSI mode of
operation on the MON3 conversion.
00b = (Default) Normal RSSI mode of operation.
01b = The fine settings of scale and offset are used for MON3 conversions.
10b = The coarse settings of scale and offset are used for MON3 conversions.
11b = Normal RSSI mode of operation.
BIT 0
EN5TO8B: This bit enables MON5–MON8 conversion (voltage of D0–D3 pins).
0 = (Default) Temperature, VCC, and MON1–MON8 conversions are enabled.
1 = Temperature, VCC, and MON1–MON4 conversions are enabled.
相關PDF資料
PDF描述
D38999/20MD18PA CONN RCPT 18POS WALL MNT W/PINS
MAX7359ETG+ IC KEY SWITCH 2WIRE 24-TQFN
USB-232-SS IC USB ASYNC SRL UART 20-SSOP
MS27473E24F61P CONN PLUG 61POS STRAIGHT W/PINS
MS27474E10F98PA CONN RCPT 6POS JAM NUT W/PINS
相關代理商/技術參數
參數描述
DS1875T+ 功能描述:ADC / DAC多通道 PON Triplexer & SFP Controller RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40
DS1875T+T&R 制造商:Maxim Integrated Products 功能描述:PON TRIPLEXER 38TQFN EP - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC SFP CTRLR/TRIPLEXER 38-TQFN 制造商:Maxim Integrated Products 功能描述:ADC / DAC Multichannel PON Triplexer & SFP Controller
DS1875T+T&R 功能描述:ADC / DAC多通道 PON Triplexer & SFP Controller RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40
DS1875T+TR 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:PON Triplexer and SFP Controller
DS1876 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:SFP Controller with Dual LDD Interface
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*