- 您現在的位置：買賣IC網 > PDF目錄1912 > DP83848HSQ/NOPB (National Semiconductor)IC TXRX ETHERNET PHYTER 40-LLP PDF資料下載
參數資料
| 型號： | DP83848HSQ/NOPB |
| 廠商： | National Semiconductor |
| 文件頁數： | 9/82頁 |
| 文件大小： | 0K |
| 描述： | IC TXRX ETHERNET PHYTER 40-LLP |
| 產品培訓模塊： | PHYTER® Family |
| 標準包裝： | 1 |
| 類型： | 收發器 |
| 驅動器/接收器數： | 1/1 |
| 規程： | 以太網 |
| 電源電壓： | 3 V ~ 3.6 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 40-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 40-LLP-EP（6x6） |
| 包裝： | 剪切帶 (CT) |
| 配用： | DP83848H-MAU-EK-ND - BOARD EVALUATION DP83848H |
| 其它名稱： | *DP83848HSQ/NOPB DP83848HSQCT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁
www.national.com
16
D
P
83
84
8H
2.1.3 Auto-Negotiation Parallel Detection
The DP83848H supports the Parallel Detection function as
defined in the IEEE 802.3u specification. Parallel Detection
requires both the 10 Mb/s and 100 Mb/s receivers to moni-
tor the receive signal and report link status to the Auto-
Negotiation function. Auto-Negotiation uses this informa-
tion to configure the correct technology in the event that the
Link Partner does not support Auto-Negotiation but is
transmitting link signals that the 100BASE-TX or 10BASE-
T PMAs recognize as valid link signals.
If the DP83848H completes Auto-Negotiation as a result of
Parallel Detection, bit 5 or bit 7 within the ANLPAR register
will be set to reflect the mode of operation present in the
Link Partner. Note that bits 4:0 of the ANLPAR will also be
set to 00001 based on a successful parallel detection to
indicate a valid 802.3 selector field. Software may deter-
mine that negotiation completed via Parallel Detection by
reading a zero in the Link Partner Auto-Negotiation Able bit
once the Auto-Negotiation Complete bit is set. If configured
for parallel detect mode and any condition other than a sin-
gle good link occurs then the parallel detect fault bit will be
set.
2.1.4 Auto-Negotiation Restart
Once Auto-Negotiation has completed, it may be restarted
at any time by setting bit 9 (Restart Auto-Negotiation) of the
BMCR to one. If the mode configured by a successful Auto-
Negotiation loses a valid link, then the Auto-Negotiation
process will resume and attempt to determine the configu-
ration for the link. This function ensures that a valid config-
uration is maintained if the cable becomes disconnected.
A renegotiation request from any entity, such as a manage-
ment agent, will cause the DP83848H to halt any transmit
data and link pulse activity until the break_link_timer
expires (~1500 ms). Consequently, the Link Partner will go
into link fail and normal Auto-Negotiation resumes. The
DP83848H
will
resume Auto-Negotiation after
the
break_link_timer has expired by issuing FLP (Fast Link
Pulse) bursts.
2.1.5 Enabling Auto-Negotiation via Software
It is important to note that if the DP83848H has been initial-
ized upon power-up as a non-auto-negotiating device
(forced technology), and it is then required that Auto-Nego-
tiation or re-Auto-Negotiation be initiated via software,
bit 12 (Auto-Negotiation Enable) of the Basic Mode Control
Register (BMCR) must first be cleared and then set for any
Auto-Negotiation function to take effect.
2.1.6 Auto-Negotiation Complete Time
Parallel detection and Auto-Negotiation take approximately
2-3 seconds to complete. In addition, Auto-Negotiation with
next page should take approximately 2-3 seconds to com-
plete, depending on the number of next pages sent.
Refer to Clause 28 of the IEEE 802.3u standard for a full
description of the individual timers related to Auto-Negotia-
tion.
2.2 Auto-MDIX
When enabled, this function utilizes Auto-Negotiation to
determine the proper configuration for transmission and
reception of data and subsequently selects the appropriate
MDI pair for MDI/MDIX operation. The function uses a ran-
dom seed to control switching of the crossover circuitry.
This implementation complies with the corresponding IEEE
802.3 Auto-Negotiation and Crossover Specifications.
Auto-MDIX is enabled by default and can be configured via
strap or via PHYCR (0x19h) register, bits [15:14].
Neither Auto-Negotiation nor Auto-MDIX is required to be
enabled in forcing crossover of the MDI pairs. Forced
crossover can be achieved through the FORCE_MDIX bit,
bit 14 of PHYCR (0x19h) register.
Note: Auto-MDIX will not work in a forced mode of opera-
tion.
相關PDF資料 |
PDF描述 |
|---|---|
| DP83848YB/NOPB | IC TXRX ETHERNET PHYTERA 48-LQFP |
| DRM4000-N00-232 | DRM 4000 MODULE |
| DRM4000L-N00-232 | MODULE DEAD RECKONING RS-232 |
| DS100BR111SQE/NOPB | IC REPEATER 10.3GBPS 2CH 24LLP |
| DS10BR254TSQX/NOPB | IC LVDS REPEAT 1.5GBPS 1:4 40LLP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DP83848I | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Industrial Temperature Single Port 10/100 Mb/s Ethernet Physical Layer Transceiver |
| DP83848I_08 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:PHYTER? - Industrial Temperature Single Port 10/100 Mb/s Ethernet Physical Layer Transceiver |
| DP83848I-MAU-EK | 功能描述:BOARD EVALUATION DP83848I RoHS:否 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
| DP83848I-MAU-EK/NOPB | 功能描述:以太網開發工具 DP83848 MAU CARD IND TEMP RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓: |
| DP83848I-POE-EK | 功能描述:以太網開發工具 DP83848 POE CARD IND TEMP RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓: |
發布緊急采購，3分鐘左右您將得到回復。