- 您現在的位置：買賣IC網 > PDF目錄1912 > DP83848HSQ/NOPB (National Semiconductor)IC TXRX ETHERNET PHYTER 40-LLP PDF資料下載
參數資料
| 型號： | DP83848HSQ/NOPB |
| 廠商： | National Semiconductor |
| 文件頁數： | 13/82頁 |
| 文件大小： | 0K |
| 描述： | IC TXRX ETHERNET PHYTER 40-LLP |
| 產品培訓模塊： | PHYTER® Family |
| 標準包裝： | 1 |
| 類型： | 收發器 |
| 驅動器/接收器數： | 1/1 |
| 規程： | 以太網 |
| 電源電壓： | 3 V ~ 3.6 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 40-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 40-LLP-EP（6x6） |
| 包裝： | 剪切帶 (CT) |
| 配用： | DP83848H-MAU-EK-ND - BOARD EVALUATION DP83848H |
| 其它名稱： | *DP83848HSQ/NOPB DP83848HSQCT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁
19
www.national.com
DP
83
84
8
H
2.5 Half Duplex vs. Full Duplex
The DP83848H supports both half and full duplex opera-
tion at both 10 Mb/s and 100 Mb/s speeds.
Half-duplex relies on the CSMA/CD protocol to handle col-
lisions and network access. In Half-Duplex mode, CRS
responds to both transmit and receive activity in order to
maintain compliance with the IEEE 802.3 specification.
Since the DP83848H is designed to support simultaneous
transmit and receive activity it is capable of supporting full-
duplex switched applications with a throughput of up to
200 Mb/s per port when operating in 100BASE-TX mode.
Because the CSMA/CD protocol does not apply to full-
duplex operation, the DP83848H disables its own internal
collision sensing and reporting functions and modifies the
behavior of Carrier Sense (CRS) such that it indicates
only receive activity. This allows a full-duplex capable
MAC to operate properly.
All modes of operation (100BASE-TX and 10BASE-T) can
run either half-duplex or full-duplex. Additionally, other
than CRS and Collision reporting, all remaining MII signal-
ing remains the same regardless of the selected duplex
mode.
It is important to understand that while Auto-Negotiation
with the use of Fast Link Pulse code words can interpret
and configure to full-duplex operation, parallel detection
can not recognize the difference between full and half-
duplex from a fixed 10 Mb/s or 100 Mb/s link partner over
twisted pair. As specified in the 802.3u specification, if a
far-end link partner is configured to a forced full duplex
100BASE-TX ability, the parallel detection state machine
in the partner would be unable to detect the full duplex
capability of the far-end link partner. This link segment
would negotiate to a half duplex 100BASE-TX configura-
tion (same scenario for 10 Mb/s).
2.6 Internal Loopback
The DP83848H includes a Loopback Test mode for facili-
tating system diagnostics. The Loopback mode is
selected through bit 14 (Loopback) of the Basic Mode
Control Register (BMCR). Writing 1 to this bit enables MII
transmit data to be routed to the MII receive outputs.
Loopback status may be checked in bit 3 of the PHY Sta-
tus Register (PHYSTS). While in Loopback mode the data
will not be transmitted onto the media. To ensure that the
desired operating mode is maintained, Auto-Negotiation
should be disabled before selecting the Loopback mode.
2.7 BIST
The DP83848H incorporates an internal Built-in Self Test
(BIST) circuit to accommodate in-circuit testing or diag-
nostics. The BIST circuit can be utilized to test the integ-
rity of the transmit and receive data paths. BIST testing
can be performed with the part in the internal loopback
mode or externally looped back using a loopback cable
fixture.
The BIST is implemented with independent transmit and
receive paths, with the transmit block generating a contin-
uous stream of a pseudo random sequence. The user can
select a 9 bit or 15 bit pseudo random sequence from the
PSR_15 bit in the PHY Control Register (PHYCR). The
received data is compared to the generated pseudo-ran-
dom data by the BIST Linear Feedback Shift Register
(LFSR) to determine the BIST pass/fail status.
The pass/fail status of the BIST is stored in the BIST sta-
tus bit in the PHYCR register. The status bit defaults to 0
(BIST fail) and will transition on a successful comparison.
If an error (mis-compare) occurs, the status bit is latched
and is cleared upon a subsequent write to the Start/Stop
bit.
For transmit VOD testing, the Packet BIST Continuous
Mode can be used to allow continuous data transmission,
setting BIST_CONT_MODE, bit 5, of CDCTRL1 (0x1Bh).
The number of BIST errors can be monitored through the
BIST Error Count in the CDCTRL1 (0x1Bh), bits [15:8].
相關PDF資料 |
PDF描述 |
|---|---|
| DP83848YB/NOPB | IC TXRX ETHERNET PHYTERA 48-LQFP |
| DRM4000-N00-232 | DRM 4000 MODULE |
| DRM4000L-N00-232 | MODULE DEAD RECKONING RS-232 |
| DS100BR111SQE/NOPB | IC REPEATER 10.3GBPS 2CH 24LLP |
| DS10BR254TSQX/NOPB | IC LVDS REPEAT 1.5GBPS 1:4 40LLP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DP83848I | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Industrial Temperature Single Port 10/100 Mb/s Ethernet Physical Layer Transceiver |
| DP83848I_08 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:PHYTER? - Industrial Temperature Single Port 10/100 Mb/s Ethernet Physical Layer Transceiver |
| DP83848I-MAU-EK | 功能描述:BOARD EVALUATION DP83848I RoHS:否 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
| DP83848I-MAU-EK/NOPB | 功能描述:以太網開發工具 DP83848 MAU CARD IND TEMP RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓: |
| DP83848I-POE-EK | 功能描述:以太網開發工具 DP83848 POE CARD IND TEMP RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓: |
發布緊急采購，3分鐘左右您將得到回復。