參數資料
型號： DNC3X3625
廠商： Lineage Power
英文描述： Hex 10/100 Mbits/s Ethernet Transceiver Macrocell(六通道 10M位/秒和100 M位/秒以太網收發器宏單元)
中文描述： 六角10/100 Mbits /秒以太網收發器宏單元（六通道1000萬位/秒和100海里位/秒以太網收發器宏單元）
文件頁數： 20/32頁
文件大?。?/td> 464K
代理商： DNC3X3625
20
DNC3X3625
10/100 Mbits/s Ethernet Transceiver Macrocell
Advance Data Sheet
March 2000
4
Register Information
(continued)
Table 13. MR0—Control Register Bit Descriptions
* The format for the bit descriptions is as follows: the first number is the register number, the second number is the bit position in the register.
R = read, W = write, NA = not applicable.
Bit
*
Type
R/W
Description
0.15 (SW_RESET)
Reset.
Setting this bit to a 1 will reset the DNC3X3625. All registers will be set
to their default state. This bit is self-clearing. The default is 0.
Loopback.
When this bit is set to 1, no data transmission will take place on the
media. Any receive data will be ignored. The loopback signal path will contain
all circuitry up to, but not including, the PMD. The default value is a 0.
Speed Selection.
The value of this bit reflects the current speed of operation
(1 = 100 Mbits/s; 0 = 10 Mbits/s). This bit will only affect operating speed when
the autonegotiation enable bit (register 0, bit 12) is disabled (0). This bit is
ignored when autonegotiation is enabled (register 0, bit 12). This bit is ANDed
with the SPEED_PIN signal.
Autonegotiation Enable.
The autonegotiation process will be enabled by set-
ting this bit to a 1. The default state is a 1.
Powerdown.
The DNC3X3625 may be placed in a low-power state by setting
this bit to a 1, both the 10 Mbits/s transceiver and the 100 Mbits/s transceiver
will be powered down. While in the powerdown state, the DNC3X3625 will
respond to management transactions. The default state is a 0.
Isolate.
When this bit is set to a 1, the MII outputs will be brought to the high-
impedance state. The default state is a 0.
Restart Autonegotiation.
Normally, the autonegotiation process is started at
powerup. The process may be restarted by setting this bit to a 1. The default
state is a 0. The NWAYDONE bit (register 1, bit 5) is reset when this bit goes to
a 1. This bit is self-cleared when autonegotiation restarts.
Duplex Mode.
This bit reflects the mode of operation (1 = full duplex; 0 = half
duplex). This bit is ignored when the autonegotiation enable bit (register 0,
bit 12) is enabled. The default state is a 0. This bit is ORed with the
F_DUP pin.
Collision Test.
When this bit is set to a 1, the DNC3X3625 will assert the
MCOL signal in response to MTX_EN.
Reserved.
All bits will read 0.
0.14 (LOOPBACK)
R/W
0.13 (SPEED100)
R/W
0.12 (NWAY_ENA)
R/W
0.11 (PWRDN)
R/W
0.10 (ISOLATE)
R/W
0.9 (REDONWAY)
R/W
0.8 (FULL_DUP)
R/W
0.7 (COLTST)
R/W
0.6:0 (RESERVED)
NA
相關PDF資料
PDF描述
DNC3X3825 Octal 10/100 Mbits/s Ethernet Transceiver Macrocell(八通道10M位/秒和100 M位/秒以太網收發器宏單元)
DNC5X3125 Gigabit Ethernet Transceiver Macrocell(千兆位以太網收發器宏單元)
DNCM00 10 Mbit/s Ethernet MAC ASIC Macrocell(10 M位/秒以太網MAC ASIC宏單元)
DNCX01 ASIC
DNCX04 Telecommunication IC
相關代理商/技術參數
參數描述
DNC3X3825 制造商:AGERE 制造商全稱:AGERE 功能描述:Octal 10/100 Mbits/s Ethernet Transceiver Macrocell
DNC-4796 功能描述:電氣外殼配件 DIN RAIL MNT CLIP 50 x 14 x 8mm RoHS:否 制造商:Hammond Manufacturing 產品:Rack Accessories 類型: 面板寬度: 面板高度: 外部寬度: 外部高度: 外部深度: 顏色:Black
DNC550RE3O/M 制造商:Denon 功能描述:OWNER'S MANUAL
DNC550RO/M 制造商:Denon Electronics 功能描述:OWNER'S MANUAL DNC550R
DNC550RS/M 制造商:Denon Electronics 功能描述:SERVICE MANUAL
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*