- 您現在的位置：買賣IC網 > PDF目錄17070 > DC798B (Linear Technology)BOARD DELTA SIGMA ADC LTC2480 PDF資料下載
參數資料
| 型號： | DC798B |
| 廠商： | Linear Technology |
| 文件頁數： | 13/42頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD DELTA SIGMA ADC LTC2480 |
| 軟件下載： | QuikEval System |
| 設計資源： | DC798B Design File DC798B Schematic |
| 標準包裝： | 1 |
| 系列： | QuikEval™ |
| ADC 的數量： | 1 |
| 位數： | 16 |
| 采樣率（每秒）： | 7.5 |
| 數據接口： | MICROWIRE?，串行，SPI? |
| 已用 IC / 零件： | LTC2480 |
| 已供物品： | 板 |
| 相關產品： | LTC2480HMS#TRPBF-ND - IC ADC DELTA SIGMA 16BIT 10MSOP LTC2480HDD#TRPBF-ND - IC ADC DELTA SIGMA 16BIT 10DFN LTC2480HDD#PBF-ND - IC ADC 16BIT SRL 7.5SPS 10DFN LTC2480HMS#PBF-ND - IC ADC 16BIT SER/SPI 10MSOP LTC2480IMS#TRPBF-ND - IC ADC 16BIT 10-MSOP LTC2480IMS#PBF-ND - IC ADC 16BIT 10-MSOP LTC2480IDD#TRPBF-ND - IC ADC 16BIT 10-DFN LTC2480CMS#TRPBF-ND - IC ADC 16BIT 10-MSOP LTC2480CMS#PBF-ND - IC ADC 16BIT 10-MSOP LTC2480CDD#TRPBF-ND - IC ADC 16BIT 10-DFN 更多... |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
LTC2480
0
2480fd
value with a temperature coefficient of 420/(27 + 273) =
1.40mV/°C (SLOPE), as shown in Figure 4. The internal
PTAT signal is used in a single-ended mode referenced
to device ground internally. The GAIN is automatically
set to one (independent of the values of GS0, GS1, GS2)
in order to preserve the PTAT property at the ADC output
code and avoid an out of range error. The 1x speed mode
with automatic offset calibration is automatically selected
for the internal PTAT signal measurement as well.
If the same VREF source is used during calibration and
temperature measurement, the actual value of the VREF
is not needed to measure the temperature as shown in
the calculation below:
T
R
V
SLOPE
R
T
C
SDO
REF
SDO
=
+
(
)
–
–
273
0
0 273 273
Reference Voltage Range
The LTC2480 external reference voltage range is 0.1V
to VCC. The converter output noise is determined by
the thermal noise of the front-end circuits, and as such,
its value in nanovolts is nearly constant with reference
voltage. Since the transition noise (600nV) is much less
than the quantization noise (VREF/217), a decrease in the
reference voltage will increase the converter resolution. A
reduced reference voltage will also improve the converter
performance when operated with an external conversion
clock (external fO signal) at substantially higher output
data rates (see the Output Data Rate section). VREF must
be ≥1.1V to use the internal temperature sensor.
The negative reference input to the converter is internally
tied to GND. GND (Pin 8) should be connected to a ground
plane through as short a trace as possible to minimize
voltage drop. The LTC2480 has an average operational
current of 160A and for 0.1Ω parasitic resistance, the
voltage drop of 16V causes a gain error of 3.2ppm for
VREF = 5V.
Input Voltage Range
The analog input is truly differential with an absolute/com-
mon mode range for the IN+ and IN– input pins extending
from GND – 0.3V to VCC + 0.3V. Outside these limits, the
ESD protection devices begin to turn on and the errors
due to input leakage current increase rapidly. Within these
limits, the LTC2480 converts the bipolar differential input
signal, VIN = IN+ – IN–, from –FS to +FS where FS = 0.5
VREF/GAIN. Outside this range, the converter indicates the
overrangeortheunderrangeconditionusingdistinctoutput
codes.Sincethedifferentialinputcurrentcancellationdoes
not rely on an on-chip buffer, current cancellation as well
as DC performance is maintained rail-to-rail.
applicaTions inForMaTion
TEMPERATURE (°C)
–60
V PTAT
(mV)
500
600
120
2480 F04
400
200
30
0
90
–30
60
300
VCC = 5V
IM = 1
FO = GND
SLOPE = 1.40mV/°C
Figure 4. Internal PTAT Signal vs Temperature
When using the internal temperature sensor, if the output
code is normalized to RSDO = VPTAT/VREF, the temperature
is calculated using the following formula:
R
V
SLOPE
T
R
V
SLOPE
K
SDO
REF
C
SDO
REF
=
°
–
in Kelvin
and
in C
273
where SLOPE is nominally 1.4mV/°C.
Since the PTAT signal can have an initial value variation
which results in errors in SLOPE, to achieve better tem-
perature measurements, a one-time calibration is needed
to adjust the SLOPE value. The converter output of the
PTAT signal, R0SDO, is measured at a known temperature
T0 (in °C) and the SLOPE is calculated as:
SLOPE
R
V
T
SDO
REF
=
+
0
0 273
This calibrated SLOPE can be used to calculate the tem-
perature.
相關PDF資料 |
PDF描述 |
|---|---|
| EVAL-AD7841EBZ | BOARD EVAL FOR AD7841 |
| XRP2525ID-2-F | IC PWR SW USB 3.0 SINGLE NSOIC8 |
| EVAL-AD7839EBZ | BOARD EVAL FOR AD7839 |
| NRS6010T4R7MMGF | INDUCTOR POWER 4.7UH 1.4A SMD |
| AD7940-DBRD | BOARD EVAL FOR AD7940 STAMP SPI |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DC-7G3EWA | 制造商:Kingbright Corporation 功能描述:Red/Green 10-seg LED lightbar, DC-7G3EWA |
| DC7G3HWA | 功能描述:LED條和陣列 7GR 3RED BARGRAFT 10 SEGMENT RoHS:否 制造商:Avago Technologies 產品:LED Light Bars 照明顏色:Red 光強度:45 mcd 封裝:Tube |
| DC-7G3HWA | 制造商:Kingbright Corporation 功能描述: |
| DC7K67J/4LR61 | 制造商:Duracell 功能描述: |
| DC8 | 制造商:Cliff Electronic Components 功能描述:SOCKET PCB DC POWER 1.3MM PK10 制造商:Cliff Electronic Components 功能描述:SOCKET, PCB, DC POWER, 1.3MM, PK10 制造商:Cliff Electronic Components 功能描述:SOCKET, PCB, DC POWER, 1.3MM, PK10, Series:DC, Gender:Receptacle, Voltage Rating |
發布緊急采購，3分鐘左右您將得到回復。