參數資料
型號： CS4362-KQZ
廠商： Cirrus Logic Inc
文件頁數： 11/42頁
文件大?。?/td> 0K
描述： IC DAC 6CH 114DB 192KHZ 48LQFP
標準包裝： 250
位數： 24
數據接口： 串行
轉換器數目： 6
電壓電源： 模擬和數字
功率耗散（最大）： 390mW
工作溫度： -10°C ~ 70°C
安裝類型： 表面貼裝
封裝/外殼： 48-LQFP
供應商設備封裝： 48-LQFP（7x7）
包裝： 托盤
輸出數目和類型： 6 電壓，單極
采樣率（每秒）： 200k
產品目錄頁面： 757 (CN2011-ZH PDF)
其它名稱： 598-1644
DS257F2
19
CS4362
Soft Ramp
Soft Ramp allows level changes, both muting and attenuation, to be implemented by incrementally ramp-
ing, in 1/8 dB steps, from the current level to the new level at a rate of 1 dB per 8 left/right clock periods.
Soft Ramp on Zero Crossing
Soft Ramp and Zero Cross Enable dictates that signal level changes, either by attenuation changes or
muting, will occur in 1/8 dB steps and be implemented on a signal zero crossing. The 1/8 dB level change
will occur after a timeout period between 512 and 1024 sample periods (10.7 ms to 21.3 ms at 48 kHz
sample rate) if the signal does not encounter a zero crossing. The zero cross function is independently
monitored and implemented for each channel.
4.3.2
Single Volume Control (SNGLVOL)
Default = 0
0 - Disabled
1 - Enabled
Function:
The individual channel volume levels are independently controlled by their respective Volume Control
Bytes when this function is disabled. The volume on all channels is determined by the A1 Channel Volume
Control Byte, and the other Volume Control Bytes are ignored when this function is enabled.
4.3.3
Soft Volume Ramp-Up After Error (RMP_UP)
Default = 0
0 - Disabled
1 - Enabled
Function:
An un-mute will be performed after executing a filter mode change, after a LRCK/MCLK ratio change or
error, and after changing the Functional Mode. When this feature is enabled, this un-mute is effected, sim-
ilar to attenuation changes, by the Soft and Zero Cross bits in the Mode Control 3 register. When disabled,
an immediate un-mute is performed in these instances.
Note:
For best results, it is recommended that this feature be used in conjunction with the RMP_DN bit.
4.3.4
MUTEC Polarity (MUTEC+/-)
Default = 0
0 - Active High
1 - Active Low
Function:
The active polarity of the MUTEC pin(s) is determined by this register. When set to 0 (default) the MUTEC
pins are high when active. When set to 1 the MUTEC pin(s) are low when active.
Note: When the on board mute circuitry is designed for active low, the MUTEC outputs will be high (un-
muted) for the period of time during reset and before this bit is enabled to 1.
相關PDF資料
PDF描述
CS4362A-DQZ IC DAC 6CH 114DB 192KHZ 48-LQFP
CS4364-CQZR IC DAC 103DB 24BIT 6CH 48-LQFP
CS4382A-DQZ IC DAC 8CH 114DB 192KHZ 48-LQFP
CS4384-CQZR IC DAC 8CH 103DB 192KHZ 48-LQFP
CS4385-DQZR IC DAC 8CH 114DB 192KHZ 48-LQFP
相關代理商/技術參數
參數描述
CS4362-KQZR 功能描述:數模轉換器- DAC IC 114dB 192kHz 6Ch DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
CS4364 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:103 dB, 192 kHz 6-Channel D/A Converter
CS4364_08 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:103 dB, 192 kHz 6-Channel D/A Converter
CS4364-CQZ 功能描述:數模轉換器- DAC IC 24bit 6Chn DAC w/ DSD Supt&Lw-Ltnc DF RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
CS4364-CQZR 功能描述:數模轉換器- DAC IC 24b 6Ch DAC w/DSD Supt/Lw-Ltnc DF RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*