- 您現在的位置：買賣IC網 > PDF目錄166217 > AMIS-30621-AGA STEPPER MOTOR CONTROLLER, 0.8 A, PDSO20 PDF資料下載
參數資料
| 型號： | AMIS-30621-AGA |
| 元件分類： | 運動控制電子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 0.8 A, PDSO20 |
| 封裝： | 300 INCH, PLASTIC, SOIC-20 |
| 文件頁數： | 33/57頁 |
| 文件大?。?/td> | 1017K |
| 代理商： | AMIS-30621-AGA |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁當前第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁
AMIS-30621 LIN Micro-stepping Motor Driver
Data Sheet
39
AMI Semiconductor
– Sept. 2007, Rev 1.5
www.amis.com
15.6.3. Preparing Frames
A preparing frame is a writing frame that warns a particular slave node that it will have to answer in the next frame (hence a reading
frame). A preparing frame is needed when a reading frame does not use a dynamically assigned direct ID. Preparing and reading
frames must be consecutive. A preparing frame will contain the physical address of the LIN slave node that must answer in the reading
frame, and will also contain a command indicating which kind of information is awaited from the slave.
The preparing frames used with the AMIS-30621 can be of Type #7 or Type #8 described below.
Type #7: two data bytes writing frame with dynamically assigned identifier.
Preparing Frame
Byte
Content
Structure
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0
Identifier
*
0
ID4
ID3
ID2
ID1
ID0
1
Data 1
1
CMD[6:0]
2
Data 2
1
AD[6:0]
Where:
(*)
According to parity computation
Type #8: eight data bytes writing frame with 0x3C identifier.
SetDualPositioning Writing Frame
Byte
Content
Structure
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0
Identifier
0
1
0
1
Data 1
AppCMD = 0x80
2
Data 2
1
CMD[6:0]
3
Data 3
1
AD[6:0]
4
Data 4
Data4[7:0]
5
Data 5
Data5[7:0]
6
Data 6
Data6[7:0]
7
Data 7
Data7[7:0]
8
Data 8
Data8[7:0]
Where:
AppCMD:
If = ‘0x80’ this indicates that data 2 contains an application command.
CMD[6:0]:
Application Command “byte”.
AD[6:0]:
Slave node physical address.
Datan[7:0]:
Data transmitted.
15.6.4. Dynamic Assignment of Identifiers
The identifier field in the LIN datagram denotes the content of the message. Six identifier bits and two parity bits are used to represent
the content. The identifiers 0x3C and 0x3F are reserved for command frames and extended frames. Slave nodes need to be very
flexible to adapt itself to a given LIN network in order to avoid conflicts with slave nodes from different manufacturers. Dynamic
assignment of the identifiers will fulfill this requirement by writing identifiers into the circuits RAM. ROM pointers are linking commands
and dynamic identifiers together. A writing frame with identifier 0x3C issued by the LIN master will write dynamic identifiers into the
RAM. One writing frame is able to assign 4 identifiers, therefore 3 frames are needed to assign all identifiers. Each ROM pointer
ROMp_x [3:0] place the corresponding dynamic identifier Dyn_ID_x [5:0] at the correct place in the RAM (see Table 1: LIN – Dynamic
Identifiers Writing Frame).
When setting <BROAD> to zero broadcasting is active and each slave on the LIN bus will store the same dynamic identifiers, otherwise
only the slave with the corresponding slave address is programmed.
相關PDF資料 |
PDF描述 |
|---|---|
| AML1005Q10NJT | 1 ELEMENT, 0.01 uH, GENERAL PURPOSE INDUCTOR, SMD |
| AMMC-6231-W10 | 16000 MHz - 32000 MHz RF/MICROWAVE WIDE BAND LOW POWER AMPLIFIER |
| AMPAL20L10AL/BKA | OT PLD, 30 ns, CDFP24 |
| AMPAL20L10AL/B3A | OT PLD, 30 ns, CQCC28 |
| AMPAL20L10AL/BLA | OT PLD, 30 ns, CDIP24 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AMIS-30621ANA | 制造商:ON Semiconductor 功能描述:STEPPER MOTOR DRVR 20SOIC - Trays 制造商:ON Semiconductor 功能描述:STEPPER MOTOR DRVR 32PIN NQFP - Tape and Reel |
| AMIS30621AUA | 功能描述:馬達/運動/點火控制器和驅動器 Stepper Motor Driver Conroller w/ LIN Bus RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| AMIS30621C6213G | 功能描述:馬達/運動/點火控制器和驅動器 LIN STEPPER DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| AMIS30621C6213RG | 功能描述:馬達/運動/點火控制器和驅動器 LIN STEPPER DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| AMIS30621C6216G | 功能描述:馬達/運動/點火控制器和驅動器 LIN STEPPER DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。