- 您現在的位置：買賣IC網 > PDF目錄385089 > AK2572 (Asahi Kasei Microsystems Co.,Ltd) APC for Burst Mode Applicable Direct Modulation Laser Diode PDF資料下載
參數資料
| 型號： | AK2572 |
| 廠商： | Asahi Kasei Microsystems Co.,Ltd |
| 英文描述： | APC for Burst Mode Applicable Direct Modulation Laser Diode |
| 中文描述： | apc的突發模式適用的直接調制激光器 |
| 文件頁數： | 46/50頁 |
| 文件大?。?/td> | 463K |
| 代理商： | AK2572 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁當前第46頁第47頁第48頁第49頁第50頁
ASAHI KASEI
[AK2572]
-46-
< MS0290-E-01>
2004/8
11. Example of Adjusting Sequence
Adjusting sequence example is shown in Table 11-1.
Table 11-1 Example of Adjusting Sequence (for Continuous mode)
Item
1
Transition to
Adjustment Mode
into Adjustment Mode via Digital I/F.
2
Set APC_FB in
open-loop operation
Modulation current are set to open-loop operation. Output current range of
I-DAC1 (or V-DAC3) for Modulation current and I-DAC2 for Bias current is
set by R_DAC1_GAIN (or R_DAC3_GAIN) and R_DAC2_GAIN respectively.
3
LD power adjustment
Set R_MOD_FF (Modulation current) and R_BIAS_FF (Bias current) so that
designated LD power is available.
4-A
PDGAIN adjustment
(When to monitor
PDMON-pin voltage)
Set R_APC_TRGT (APC target)
＝
”1 0000” (its center value), and after
making APC setting (R_APC_FB_SET, R_APC_FF_SET, R_MOD_FBRT
and R_BIAS_FBRT when both Bias and Modulation currents are used for
APC_FB setting), jump to “Step 5” in this table.
4-B
PDGAIN adjustment
(When to monitor
PDMON-pin voltage is
impossible)
when both Bias and Modulation currents are used for APC_FB setting),
Then APC_FB function is activated and LD power is lowered. Adjust
R_PDGAIN so that LD power reaches a closest amount to the designated
power level, and jump to “Step 5” in this table.
5
APC_FB
target adjustment
reaches its designated power level.
6
Read-out of sensed
temperature data
7
Calculation of
temperature
characteristic
temperature points or more and make the look-up table of I-DAC1 (or
V-DAC3) and I-DAC2 with referring the measured data
If the adjustment is executed at single temperature point, make the look-up
table with the measured data and On-chip temperature sensor gain (1.5
℃
/LSB [Typ.]).
8
Write the adjustment
data into EEPROM
(2) Issue a command to make a transition into EEPROM Access Mode via
Digital I/F.
(3) Write adjusting data into EEPROM.
(4) Verify that correct data is written, by reading out the written data.
9
Transition to
Self-Operation Mode
Self-Operation Mode via Digital I/F. Then the AK2572 automatically initiates
its operation in accordance with the setting data retained in EEPROM.
Contents
After releasing the Write Protection, issue a command to make a transition
Set R_APC_FB_SET=”0”
、
R_APC_FF_SET=”3”, and Bias current and
Adjust PDMON-pin voltage when the designated LD power is output.
Adjust PDMON-pin output voltage to be 1 [V] by R_PDGAIN.
Set R_APC_TRGT (APC target)
＝
”1 0000” (its center value) and R_PDGAIN
＝
”00 0000” (23.5dB, Maximum gain), then make APC setting
(R_APC_FB_SET, R_APC_FF_SET, R_MOD_FBRT and R_BIAS_FBRT
Adjust DAC_APC setting value (R_APC_TRGT) so that LD optical power
Read out the LSI chip-surface temperature equivalent value (R_TEMP).
In order to adjust the temperature characteristic of LD, vary temperature
and repeat “Steps 2 ~ 6” above when adjustment is made at 2 different
(1) Prepare the data to be written into EEPROM based on LD adjusting data.
After writing data into EEPROM, issue a command to make a transition to
相關PDF資料 |
PDF描述 |
|---|---|
| AK2573A | 125M / 156M Laser Diode Driver + APC |
| AK2573AVB | 125M / 156M Laser Diode Driver + APC |
| AK2574 | 156M Laser Diode Driver + APC for Burst Mode |
| AK2574VB | 156M Laser Diode Driver + APC for Burst Mode |
| AK4103A | 192 KHZ 24 BIT DIT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AK2573A | 制造商:AKM 制造商全稱:AKM 功能描述:125M / 156M Laser Diode Driver + APC |
| AK2573AVB | 制造商:AKM 制造商全稱:AKM 功能描述:125M / 156M Laser Diode Driver + APC |
| AK2574 | 制造商:AKM 制造商全稱:AKM 功能描述:156M Laser Diode Driver + APC for Burst Mode |
| AK2574VB | 制造商:AKM 制造商全稱:AKM 功能描述:156M Laser Diode Driver + APC for Burst Mode |
| AK2581HB-AT | 制造商:ADDA Corporation 功能描述:AC-FAN, 254X89 MM, 115/60 VOLT 制造商:ADDA Corporation 功能描述:AXIAL FAN 254MM 115VAC 620mA 制造商:ADDA Corporation 功能描述:AXIAL FAN, 254MM, 115VAC, 620mA 制造商:ADDA Corporation 功能描述:AK Series 2100/2000 RPM 254 x 89 mm 115 V 680/630 CFM Ball Bearing AC Fan 制造商:ADDA Corporation 功能描述:AXIAL FAN, 254MM, 115VAC, 620mA; Frame Dimensions:254mm x 89mm; Supply Voltage:115VAC; Current Rating:620mA; Flow Rate - Imperial:630cu.ft/min; Flow Rate - Metric:19.244m /min; Noise Rating:62dBA; Bearing Type:Ball; Series:AK25489 ;RoHS Compliant: Yes 制造商:ADDA 功能描述:AK Series 2100/2000 RPM 254 x 89 mm 115 V 680/630 CFM Ball Bearing AC Fan |
發布緊急采購，3分鐘左右您將得到回復。