- 您現在的位置：買賣IC網 > PDF目錄385089 > AK2572 (Asahi Kasei Microsystems Co.,Ltd) APC for Burst Mode Applicable Direct Modulation Laser Diode PDF資料下載
參數資料
| 型號： | AK2572 |
| 廠商： | Asahi Kasei Microsystems Co.,Ltd |
| 英文描述： | APC for Burst Mode Applicable Direct Modulation Laser Diode |
| 中文描述： | apc的突發模式適用的直接調制激光器 |
| 文件頁數： | 15/50頁 |
| 文件大小： | 463K |
| 代理商： | AK2572 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁
ASAHI KASEI
[AK2572]
-15-
<MS0290-E-01>
2004/8
< Linear interpolation of E_EXTRA_TC >
Given that the detected temperature data are R_TEMP
［
7:0
］＝
z
＝
8y, 8y+1,
, 8y+7, R_TEMP
［
7:3
］＝
y,
and the temperature compensated data retained in EEPROM is E_EXTRA_TC(y), and data calculated by
linear interpolation is R_EXTRA(z) (DAC loading E_EXTRA_TC data is selected by RE_MODV_SEL ),
R_EXTRA(z)
＝
E_EXTRA_TC(y
－
1)
＋｛
E_EXTRA_TC(y)
－
E_EXTRA_TC(y
－
1)
｝×
R_TEMP
［
2:0
］
/ 8
But at y
＝
0 (R_TEMP
［
7:0
］＝
z
＝
0 ~ 7), E_EXTRA_TC(y)
＝
E_EXTRA_TC(y
－
1)
＝
E_EXTRA_TC(0)
In order to keep the optical power of LD constant by APC_FF method, regardless of environmental temperature
changes, it is necessary to write and store the data of Bias current and Modulation current at each in the
temperature-corresponding EEPROM address when to adjust each LD module. In normal operation, On-chip
oscillator for temperature compensation of the current to drive LD modules automatically executes the
temperature detection and the current setting.
Those temperature compensated data for Bias current, Modulation current and EXTRA_DAC which are all
derived from the linear interpolation, have approximately 0.75
℃
resolution and can automatically adjust LD
current and reference voltage for external circuit in approximately 0.75
℃
step. The On-chip temperature sensor
is designed to cover the temperature range from - 40
℃
~ +115
℃
under the ADC operating voltage range (0 ~
2.2 V [Typ.]). As to the relation between temperature sensor and ADC code, please refer to Section “4.4 On-chip
Temperature Sensor Characteristics“.
Figure 4-2 APC_FF Functional Block Diagram
ADC
(8bit)
EEPROM
I-DAC1
(V-DAC3)
R_TEMP[7:1]
R_MOD_FF
Address
Data
LDD
Output voltage from
TEMPSENS is
A-to-D converted
On-chip Temperature
Sensor (TEMPSENS)
I-DAC2
Memory for
Imod
(I-DAC1 or V-DAC3)
128 address
Memory for
Ibias
(I-DAC2)
128 address
R_BIAS_FF
LD
Temperature
t
[
℃
]
V
V
[
Output voltage proportionally
changes in response to
temperature change
Set the read out data into
I-DAC1(V-DAC3) and
I-DAC2, then control LD
current
A proper current value data
should be written in advance
at each address location
which corresponds to each
temperature value
Ibias
Imod
Read out the data in
EEPROMwith referring
Digital code as EEPROM
address
E(x-1) + {E(x)-E(x-1)} *
2
R_MOD_FF, R_BIAS_FF (Linear interpolation of APC_FF data):
E(x): E_BIAS_TC or E_MOD_TC at x=R_TEMP[7:1]
R(z): R_BIAS_FF or R_MOD_FF at z=R_TEMP[7:0]=2x, 2x+1
R
Digital code changes in
response to temperature
change
ADC output
TEMPSENS output
R(z) =
R_TEMP[0]
Temperature
t
[
℃
]
4.2
APC_FB Function
APC_FB functional block diagram is shown in Figure 4-3.
In APC_FB block, an amplified PDIN voltage by gain value (vpd) and DAC_APC output voltage (vapc_ref) are
compared at APC_COMP, and the feedback current (R_APC_FB) is calculated at digital filter so that vpd and
vapc_ref are equal. The cut-off frequency (fpd), which is fixed by Rpd and Cpd, should be set as follows:
5 kHz
＜
fpd
＜
10 kHz
相關PDF資料 |
PDF描述 |
|---|---|
| AK2573A | 125M / 156M Laser Diode Driver + APC |
| AK2573AVB | 125M / 156M Laser Diode Driver + APC |
| AK2574 | 156M Laser Diode Driver + APC for Burst Mode |
| AK2574VB | 156M Laser Diode Driver + APC for Burst Mode |
| AK4103A | 192 KHZ 24 BIT DIT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AK2573A | 制造商:AKM 制造商全稱:AKM 功能描述:125M / 156M Laser Diode Driver + APC |
| AK2573AVB | 制造商:AKM 制造商全稱:AKM 功能描述:125M / 156M Laser Diode Driver + APC |
| AK2574 | 制造商:AKM 制造商全稱:AKM 功能描述:156M Laser Diode Driver + APC for Burst Mode |
| AK2574VB | 制造商:AKM 制造商全稱:AKM 功能描述:156M Laser Diode Driver + APC for Burst Mode |
| AK2581HB-AT | 制造商:ADDA Corporation 功能描述:AC-FAN, 254X89 MM, 115/60 VOLT 制造商:ADDA Corporation 功能描述:AXIAL FAN 254MM 115VAC 620mA 制造商:ADDA Corporation 功能描述:AXIAL FAN, 254MM, 115VAC, 620mA 制造商:ADDA Corporation 功能描述:AK Series 2100/2000 RPM 254 x 89 mm 115 V 680/630 CFM Ball Bearing AC Fan 制造商:ADDA Corporation 功能描述:AXIAL FAN, 254MM, 115VAC, 620mA; Frame Dimensions:254mm x 89mm; Supply Voltage:115VAC; Current Rating:620mA; Flow Rate - Imperial:630cu.ft/min; Flow Rate - Metric:19.244m /min; Noise Rating:62dBA; Bearing Type:Ball; Series:AK25489 ;RoHS Compliant: Yes 制造商:ADDA 功能描述:AK Series 2100/2000 RPM 254 x 89 mm 115 V 680/630 CFM Ball Bearing AC Fan |
發布緊急采購，3分鐘左右您將得到回復。