參數資料
型號： AK2572
廠商： Asahi Kasei Microsystems Co.,Ltd
英文描述： APC for Burst Mode Applicable Direct Modulation Laser Diode
中文描述： apc的突發模式適用的直接調制激光器
文件頁數： 30/50頁
文件大?。?/td> 463K
代理商： AK2572
ASAHI KASEI
[AK2572]
-30-
< MS0290-E-01>
2004/8
8.
Start-Up Setting in SFP Support Mode
8.1
TXFAULT Detection at Power-Up and after Release from Shutdown
8.1.1 OPTALM
In SFP support mode setting (RE_SFP_SET
＝
”0”), a mask time can be programmed for TXFAULT detection by
OPTALM during the shutdown release so that a time constant delay derived from the external Rpd and Cpd for
detection of the averaged monitor-PD current at the turning-on of LD must be taken into consideration. Block
diagram in Figure 8-1, and pre-settable mask time relation in Table 8-1 are shown.
In the AK2572, the delay time can be shortened by accelerated start-up setting which is made by initial value
setting function of R_APC_FB and so on.
But when OPTALM is selected as one of the TXFAULT target ALMs, and a mask time is set to be shortened, be
noted that LD optical power will not reach the expected level within the mask time and it may be shutdown
through OPTALM detection to TXFAULT control sequence if initial set value of APC_FF or APC_FB is far off.
Figure 8-1 OPTALM Detection Block Diagram
TXFAULT
CONTROL
APC Feedback value (R_APC_FB)
PDGAIN
Monitor
PD
DIGITAL
FILTER
APC target
(R_APC_TRGT)
OPTALM
_COMP
OPTALM threshold
(optalm_ref)
PDIN
Rpd
Cpd
DAC_APC
ATT
vpd
vapc_ref
APC_
COMP
OPALM setting
(R_OPTALM)
PDGAIN setting
(RE_PDGAIN)
LD
A time constant delay at
shutdown release derived
from the external Rpd and
Cpd must be taken into
consideration
Table 8-1 Time to Valid TXFAULT Detection by OPTALM
RE_
SFP_SET
_OPTALM
INIT_SET
0
RE_TIMER
RE_APC_
RE_APC
_FF_SET
x
00, 01, 10
11
x
x
Mask time for TXFAULT
detection by OPTALM
160 ms [Typ.]
160 ms [Typ.]
2 ms [Typ.]
2 ms [Typ.]
0 ms
Note
x
0
x
1
x
Accelerated start-up setting
Accelerated start-up setting
Non-support SFP
0
1
1
x
8.1.2
EXTALM1, EXTALM2
In SFP support mode setting (RE_SFP_SET
＝
”0”), a mask time can be set for TXFAULT detection by
EXTALM1 and EXTALM2 at the shutdown release.
In Table 8-2, a delay time relation to be set is shown.
Table 8-2 Time to Valid TXFAULT Detection by EXTALM1, EXTALM2
RE_TIMER_EXTALM1
RE_TIMER_EXTALM2
0
0
1
1
X
RE_SFP_SET
Mask time for TXFAULT detection
by EXTALM1, EXTALM 2
0 ms
2 ms [Typ.]
0 ms
Note
Non-support SFP
相關PDF資料
PDF描述
AK2573A 125M / 156M Laser Diode Driver + APC
AK2573AVB 125M / 156M Laser Diode Driver + APC
AK2574 156M Laser Diode Driver + APC for Burst Mode
AK2574VB 156M Laser Diode Driver + APC for Burst Mode
AK4103A 192 KHZ 24 BIT DIT
相關代理商/技術參數
參數描述
AK2573A 制造商:AKM 制造商全稱:AKM 功能描述:125M / 156M Laser Diode Driver + APC
AK2573AVB 制造商:AKM 制造商全稱:AKM 功能描述:125M / 156M Laser Diode Driver + APC
AK2574 制造商:AKM 制造商全稱:AKM 功能描述:156M Laser Diode Driver + APC for Burst Mode
AK2574VB 制造商:AKM 制造商全稱:AKM 功能描述:156M Laser Diode Driver + APC for Burst Mode
AK2581HB-AT 制造商:ADDA Corporation 功能描述:AC-FAN, 254X89 MM, 115/60 VOLT 制造商:ADDA Corporation 功能描述:AXIAL FAN 254MM 115VAC 620mA 制造商:ADDA Corporation 功能描述:AXIAL FAN, 254MM, 115VAC, 620mA 制造商:ADDA Corporation 功能描述:AK Series 2100/2000 RPM 254 x 89 mm 115 V 680/630 CFM Ball Bearing AC Fan 制造商:ADDA Corporation 功能描述:AXIAL FAN, 254MM, 115VAC, 620mA; Frame Dimensions:254mm x 89mm; Supply Voltage:115VAC; Current Rating:620mA; Flow Rate - Imperial:630cu.ft/min; Flow Rate - Metric:19.244m /min; Noise Rating:62dBA; Bearing Type:Ball; Series:AK25489 ;RoHS Compliant: Yes 制造商:ADDA 功能描述:AK Series 2100/2000 RPM 254 x 89 mm 115 V 680/630 CFM Ball Bearing AC Fan
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*