- 您現在的位置：買賣IC網 > PDF目錄1901 > ADV7188BSTZ (Analog Devices Inc)IC DECODER VID MULTIFORM 80LQFP PDF資料下載
參數資料
| 型號： | ADV7188BSTZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 72/112頁 |
| 文件大小： | 0K |
| 描述： | IC DECODER VID MULTIFORM 80LQFP |
| 標準包裝： | 1 |
| 類型： | 視頻解碼器 |
| 應用： | 機頂盒，視頻播放器，錄音機 |
| 電壓 - 電源，模擬： | 3.15 V ~ 3.45 V |
| 電壓 - 電源，數字： | 1.65 V ~ 2 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 80-LQFP |
| 供應商設備封裝： | 80-LQFP（14x14） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁當前第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁
ADV7188
Rev. A | Page 62 of 112
VDP_CGMS_WSS_CHNGD_CLR, Address 0x4F [2],
User Sub Map
1—Clears the VDP_CGMS_WSS_CHNGD_Q bit.
VDP_GS_VPS_PDC_UTC_CHNG_CLR,
Address 0x4F [4], User Sub Map
1—Clears the VDP_GS_VPS_PDC_UTC_CHNG_Q bit.
VDP_VITC_CLR, Address 0x4F [6], User Sub Map
1—Clears the VDP_VITC_Q bit.
STANDARD DETECTION AND IDENTIFICATION
The standard detection and identification (STDI) block of the
ADV7188 monitors the synchronization signals received on the
SOY pin. STDI_LINE_COUNT_MODE must be set to 1 to enable
the STDI block and achieve valid synchronization signal analysis.
Four key measurements are performed:
Block Length BL [13:0]. This is the number of clock cycles in
a block of eight lines. From this, the time duration of one line
can be concluded. Please note that the crystal frequency
determines the clock cycle and that a crystal frequency of
28.63636 MHz should be used for the ADV7188.
Line Count in Field LCF [10:0]. The LCF [10:0] readback
value is the number of lines between two vsyncs, that is,
over one field.
Line Count in Vsync LCVS [4:0]. The LCVS [4:0] readback
value is the number of lines within one vsync period.
Field Length FCL [12:0]. This is the number of clock cycles
in 1/256th of a field. Multiplying this value by 256 calculates
the field length in clock cycles.
By interpreting these four parameters, it is possible to
distinguish among the types of input signals.
A data valid flag, STDI_VALID, is provided that is held low
during the measurements. The four parameters should only be
read after the STDI_VALID flag has gone high. Refer to Table 76
for information on the readback values.
Notes
Types of synchronization pulses include horizontal
synchronization pulses, equalization and serration
pulses, and Macrovision pulses.
Macrovision pseudosynchronization and AGC pulses are
counted by the STDI block in normal readback mode. This
does not prohibit the identification of the video signal.
The ADV7188 only measures the parameters; it does not take
any action based on these measurements. Therefore, the part
helps to identify the input to avoid problems in the scheduling
of a system controller, but it does not reconfigure itself.
STDI_DVALID, Standard Identification Data Valid Read
Back, Address 0xB1 [7]
X—This bit is set by the ADV7188 as soon as the measurements
of the STDI block are finished. A high level signals the validity
of the BL, LCVS, LCF, and STDI_INTLCD parameters. To
prevent false readouts, especially during the signal acquisition,
the DVALID bit only goes high after recording four fields with
the same length. As a result, the measurements can require up
to five fields to finish.
STDI_LINE_COUNT_MODE, Address 0x86 [3]
0 (default)—Disables the STDI functionality.
1—Enables STDI functionality. This enables valid readback of
the STDI block registers.
BL [13:0], Block Length Readback, Address 0xB1 [5:0],
Address 0xB2 [7:0]
XX XXXX XXXX XXXX—Number of clock cycles in a block of
eight lines of incoming video. Data is only valid if STDI_DVALID
is high.
LCVS [4:0], Line Count in Vsync Readback,
Address 0xB3 [7:3]
X XXXX—Number of lines within a vertical synchronization
period. Data is only valid if STDI_DVALID is high.
LCF [10:0], Line Count in Field Readback,
Address 0xB3 [2:0], Address 0xB4 [7:0]
XX XXXX XXXX—Number of lines between two vsyncs per
one field/frame. Data is only valid if STDI_DVALID is high.
FCL [12:0], 1/256th of Field Length in Number of Crystal
Clocks Read back, Address 0xCA [4:0], Address 0xCB [7:0]
XXX—Number of crystal clocks (with the recommended
28.63636 MHz frequency) in 1/256th of a field. Data is only
valid if STDI_DVALID is high.
相關PDF資料 |
PDF描述 |
|---|---|
| ADV7189BBSTZ | IC VIDEO DECODER SDTV 80-LQFP |
| ADV7194KSTZ | IC ENCODER VIDEO EXT-10 80-LQFP |
| ADV7202KSTZ | IC CODEC VIDEO 10BIT 64LQFP |
| ADV7311KST | IC VID ENC 6-12BIT DAC'S 64LQFP |
| ADV7321KSTZ | IC VID ENC 6-12BIT DAC'S 64LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADV7189 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Multiformat SDTV Video Decoder |
| ADV7189B | 制造商:AD 制造商全稱:Analog Devices 功能描述:Multiformat SDTV Video Decoder |
| ADV7189BBSTZ | 功能描述:IC VIDEO DECODER SDTV 80-LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 編碼器，解碼器，轉換器 系列:- 產品變化通告:Development Systems Discontinuation 26/Apr/2011 標準包裝:1 系列:- 類型:編碼器 應用:DVB-S.2 系統 電壓 - 電源，模擬:- 電壓 - 電源，數字:- 安裝類型:- 封裝/外殼:模塊 供應商設備封裝:模塊 包裝:散裝 其它名稱:Q4645799 |
| ADV7189BBSTZ268H | 制造商:AD 制造商全稱:Analog Devices 功能描述:Multiformat SDTV Video Decoder |
| ADV7189BBSTZ268H2 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Multiformat SDTV Video Decoder |
發布緊急采購，3分鐘左右您將得到回復。