- 您現在的位置：買賣IC網 > PDF目錄374044 > ADUuC7027BSTZ62-RL (Analog Devices, Inc.) Precision Analog Microcontroller 12-bit Analog I/O, ARM7TDMI MCU PDF資料下載
參數資料
| 型號： | ADUuC7027BSTZ62-RL |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | Precision Analog Microcontroller 12-bit Analog I/O, ARM7TDMI MCU |
| 中文描述： | 精密模擬微控制器的12位模擬I / O，ARM7TDMI的微控制器 |
| 文件頁數： | 58/92頁 |
| 文件大?。?/td> | 850K |
| 代理商： | ADUUC7027BSTZ62-RL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁當前第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁
ADuC7019/20/21/22/24/25/26/27
This situation is illustrated in Figure 59, where it can be seen
that both the 0H and 1L signals are identical, because
PWMCH0 = PWMCH1 and the crossover bit for phase B is set.
Rev. A | Page 58 of 92
0
PWMCH0 =
PWMCH1
0H
0L
1H
1L
2H
2L
PWMCH0 =
PWMCH1
2 × PWMDAT1
2 × PWMDAT1
PWMDAT0
PWMDAT0
Figure 59. Active LO PWM Signals Suitable for ECM Control,
PWMCH0 = PWMCH1, Crossover 1H/1L Pair and Disable
0L, 1H, 2H, and 2L Outputs in Single Update Mode.
In addition, the other four signals (0L, 1H, 2H, and 2L) have
been disabled by setting the appropriate enable/disable bits of
the PWMEN register. In Figure 59, the appropriate value for
the PWMEN register is 0×00A7. In normal ECM operation,
each inverter leg is disabled for certain periods of time so that
the PWMEN register is changed based on the position of the
rotor shaft (motor commutation).
Gate Drive Unit
The gate drive unit of the PWM controller adds features that
simplify the design of isolated gate-drive circuits for PWM
inverters. If a transformer-coupled, power device, gate-drive
amplifier is used, then the active PWM signal must be chopped at
a high frequency. The 10-bit read/write PWMCFG register
programs this high frequency chopping mode. The chopped
active PWM signals can be required for the high-side drivers
only, the low-side drivers only, or both the high-side and low-
side switches. Therefore, independent control of this mode for
both high-side and low-side switches is included with two
separate control bits in the PWMCFG register.
Typical PWM output signals with high frequency chopping
enabled on both high-side and low-side signals are shown in
Figure 60. Chopping of the high-side PWM outputs (0H, 1H,
and 2H) is enabled by setting Bit 8 of the PWMCFG register.
Chopping of the low-side PWM outputs (0L, 1L, and 2L) is
enabled by setting Bit 9 of the PWMCFG register. The high
chopping frequency is controlled by the 8-bit word (GDCLK)
placed in Bit 0 to Bit 7 of the PWMCFG register. The period of
this high frequency carrier is
T
CHOP
= (4 × (
GDCLK
+ 1)) ×
t
CORE
The chopping frequency is therefore an integral subdivision of
the MicroConverter core frequency
f
CHOP
=
f
CORE
/(4 × (
GDCLK
+ 1))
The GDCLK value can range from 0 to 255, corresponding to
a programmable chopping frequency rate from 40.8 kHz to
10.44 MHz for a 41.78 MHz core frequency. The gate drive
features must be programmed before operation of the PWM
controller and are typically not changed during normal
operation of the PWM controller. Following a reset, all bits of
the PWMCFG register are cleared so that high frequency
chopping is disabled, by default.
0
PWMCH0
PWMCH0
PWMDAT0
PWMDAT0
0L
0H
2 × PWMDAT1
4 × (GDCLK + 1) ×
t
CORE
2 × PWMDAT1
Figure 60. Typical PWM Signals with High Frequency Gate Chopping Enabled
on Both High-Side and Low-Side Switches
PWM Shut Down
In the event of external fault conditions, it is essential that the
PWM system be instantaneously shut down in a safe fashion. A
low level on the PWM
TRIP
pin provides an instantaneous,
asynchronous (independent of the MicroConverter core clock)
shutdown of the PWM controller. All six PWM outputs are
placed in the off state, that is, high state. In addition, the
PWMSYNC pulse is disabled. The PWM
TRIP
pin has an internal
pull-down resistor to disable the PWM if the pin becomes
disconnected. The state of the PWM
TRIP
pin can be read from
Bit 3 of the PWMSTA register.
If a PWM shutdown command occurs, a PWMTRIP
interrupt is
generated, and internal timing of the three-phase timing unit of
the PWM controller is stopped. Following a PWM shutdown, the
PWM can only be re-enabled (in a PWMTRIP interrupt service
routine, for example) by writing to all of the PWMDAT0,
PWMCH0, PWMCH1, and PWMCH2 registers. Provided that
the external fault is cleared and the PWMTRIP
is returned to a
high level, the internal timing of the three-phase timing unit
resumes, and new duty-cycle values are latched on the next
PWMSYNC boundary.
Note that the PWMTRIP interrupt is available in IRQ only,
and the PWMSYNC interrupt is available in FIQ only. Both
interrupts share the same bit in the interrupt controller.
Therefore, only one of the interrupts can be used at once.
See the Interrupt System section for further details.
相關PDF資料 |
PDF描述 |
|---|---|
| ADV101 | Circular Connector; No. of Contacts:6; Series:LJT07R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:9; Circular Contact Gender:Socket; Circular Shell Style:Jam Nut Receptacle; Insert Arrangement:9-35 |
| ADV101KN30 | Circular Connector; No. of Contacts:4; Series:LJT07R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:9; Circular Contact Gender:Pin; Circular Shell Style:Jam Nut Receptacle; Insert Arrangement:9-44 |
| ADV101KN50 | Circular Connector; No. of Contacts:4; Series:LJT07R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:9; Circular Contact Gender:Socket; Circular Shell Style:Jam Nut Receptacle; Insert Arrangement:9-44 |
| ADV101KN80 | Circular Connector; No. of Contacts:6; Series:LJT07R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:9; Circular Contact Gender:Pin; Circular Shell Style:Jam Nut Receptacle; Insert Arrangement:9-6 |
| ADV101KP30 | Circular Connector; No. of Contacts:3; Series:LJT07R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:9; Circular Contact Gender:Pin; Circular Shell Style:Jam Nut Receptacle; Insert Arrangement:9-98 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADUX1020BCPZRL7 | 功能描述:Optical Sensor Ambient, Gesture 960nm I2C 8-WFDFN Exposed Pad 制造商:analog devices inc. 系列:- 包裝:剪切帶（CT） 零件狀態:有效 類型:環境，手勢 波長:960nm 接近探測:是 輸出類型:I2C 電壓 - 電源:1.8 V ~ 3.3 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商器件封裝:8-LFCSP（2x3） 標準包裝:1 |
| ADUX1020-EVAL-SDP | 功能描述:ADUX1020 - Light and Proximity Sensor Evaluation Board 制造商:analog devices inc. 系列:- 零件狀態:有效 傳感器類型:光線和近程 感應范圍:- 接口:I2C 靈敏度:- 電壓 - 電源:- 嵌入式:- 所含物品:3 個板，線纜 使用的 IC/零件:ADUX1020 標準包裝:1 |
| ADUX1020-EVALZ-LED | 功能描述:ADUX1020 - Interface Board 制造商:analog devices inc. 系列:- 零件狀態:有效 配件類型:接口板 配套使用產品/相關產品:ADUX1020 標準包裝:1 |
| ADV001-00E | 制造商:RHOPOINT 制造商全稱:RHOPOINT COMPONENTS 功能描述:ADV Sensors |
| ADV001-10E | 制造商:RHOPOINT 制造商全稱:RHOPOINT COMPONENTS 功能描述:ADV Sensors |
發布緊急采購，3分鐘左右您將得到回復。