參數資料
型號： ADT7518ARQZ
廠商： Analog Devices Inc
文件頁數： 29/40頁
文件大?。?/td> 891K
描述： IC SENSOR TEMP QD ADC/DAC 16QSOP
標準包裝： 98
功能： 溫度監控系統（傳感器）
傳感器類型： 內部和外部
感應溫度： -40°C ~ 120°C，外部傳感器
精確度： ±3°C（最小值）
拓?fù)洌?/td> ADC，比較器，多路復用器，寄存器庫
輸出類型： I²C?，MICROWIRE?，QSPI?，SPI?
輸出警報： 無
輸出風扇： 無
電源電壓： 2.7 V ~ 5.5 V
工作溫度： -40°C ~ 120°C
安裝類型： 表面貼裝
封裝/外殼： 16-SSOP（0.154"，3.90mm 寬）
供應商設備封裝： 16-QSOP
包裝： 托盤
產品目錄頁面： 798 (CN2011-ZH PDF)
 
ADT7518
 
Rev. A | Page 29 of 40
Table 30.
Bit
Function
C0
This bit enables/disables conversions in round robin
and single-channel mode. ADT7518 powers up in round
robin mode but monitoring is not initiated until this bit
is set. The default = 0.
0 = Stop monitoring.
1 = Start monitoring.
C2:C1   Selects between the two different analog inputs on Pins
7 and 8. ADT7518 powers up with AIN1 and AIN2
selected.
00 = AIN1 and AIN2 selected.
01 = Undefined.
10 = External TDM selected.
11 = Undefined.
C3
Selects between digital (LDAC) and analog inputs (AIN3)
on Pin 9. When AIN3 is selected, Bit C3 of the Control
Configuration 3 register is masked and has no effect
until LDAC is selected as the input on Pin 9.
0 = LDAC selected.
1 = AIN3 selected.
C4
Reserved. Write 0 only.
C5
0 = Enable INT/INT
 output.
1 = Disable INT/INT
 output.
C6
Configures INT/INT
 output polarity.
0 = Active low.
1 = Active high.
PD
Power-Down Bit. Setting this bit to 1 puts the ADT7518
into standby mode. In this mode, both ADC and DACs
are fully powered down, but the serial interface is still
operational. To power up the part again, just write 0 to
this bit.
 
Control Configuration 2 Register (Read/Write)
[Address = 19h]
This configuration register is an 8-bit read/write register that is
used to set up some of the operating modes of the ADT7518.
 
Table 31. Control Configuration 2
D7
D6
D5
D4
D3
D2
D1
D0
C7
C6
C5
C4
C3
C2
C1
C0
0*
0*
0*
0*
0*
0*
0*
0*
* Default settings at power-up
Table 32.
Bit     Function
C2:0   In single-channel mode, these bits select between V
DD
,
the internal temperature sensor, external temperature
sensor/AIN1, AIN2, AIN3, and AIN4 for conversion. The
default is VDD.
000 = VDD.
001 = Internal temperature sensor.
010 = External temperature sensor/AIN1. (Bits C1:C2 of
the Control Configuration 1 register affect this selection).
011 = AIN2.
100 = AIN3.
Bit     Function
101 = AIN4.
110111 = Reserved.
C3
Reserved.
C4
Selects between single-channel and round robin conver-
sion cycle. The default is round robin.
0 = Round robin.
1 = Single channel.
C5
Default condition is to average every measurement on all
channels 16 times. This bit disables this averaging.
Channels affected are temperature, analog inputs, and
V
DD
.
0 = Enable averaging.
1 = Disable averaging.
C6
SMBus timeout on the serial clock puts a 25 ms limit on
the pulse width of the clock, ensuring that a fault on the
master SCL does not lock up the SDA line.
0 = Disable SMBus timeout.
1 = Enable SMBus timeout.
C7
Software Reset. Setting this bit to 1 causes a software
reset. All registers and DAC outputs will reset to their
default settings.
 
Control Configuration 3 Register (Read/Write)
[Address = 1Ah]
This configuration register is an 8-bit read/write register that is
used to set up some of the operating modes of the ADT7518.
 
Table 33. Control Configuration 3
D7
D6
D5
D4
D3
D2
D1
D0
C7
C6
C5
C4
C3
C2
C1
C0
0*
0*
0*
0*
0*
0*
0*
0*
*Default settings at power-up 
Table 34.
Bit     Function
C0
Selects between fast and slow ADC conversion speeds.
0 = ADC clock at 1.4 kHz.
1 = ADC clock at 22.5 kHz. D+ and D analog filters are
disabled.
C2:1    Reserved. Write 0 only.
C3
0 = LDAC
 pin controls updating of DAC outputs.
1 = DAC configuration register and LDAC configuration
register control updating of DAC outputs.
C4
Selects the ADC reference to be either internal VREF or VDD
for analog inputs.
0 = Internal V
REF.
1 = V
DD
.
C5
Setting this bit selects DAC A voltage output to be
proportional to the internal temperature measurement.
C6
Setting this bit selects DAC B voltage output to be
proportional to the external temperature measurement.
C7
Reserved. Write 0 only.
 
相關PDF資料
PDF描述
AT30TS00-MAH-T SENSOR DGTL TEMP I2C/SMBUS 8WDFN
AT30TSE002B-MAH-T SENSOR DGTL TEMP I2C/SMBUS 8WDFN
BD3504FVM-TR IC REG CTRLR SGL POS ADJ 8MSOP
BD3521FVM-TR IC REG CTRLR SGL 1.5V MSOP8
BD9153MUV-E2 IC REG TRPL BCK/LINEAR 24VQFN
相關代理商/技術參數
參數描述
ADT7518ARQZ-REEL 制造商:Analog Devices 功能描述:Temp Sensor Analog Serial (4-Wire, SPI, I2C) 16-Pin QSOP T/R
ADT7518ARQZ-REEL7 制造商:Analog Devices 功能描述:Temp Sensor Analog Serial (4-Wire, SPI, I2C) 16-Pin QSOP T/R
ADT7519 制造商:AD 制造商全稱:Analog Devices 功能描述:SPI-/I2C-Compatible, Temperature Sensor,4-Channel ADC and Quad Voltage Output
ADT7519ARQ 制造商:Analog Devices 功能描述:Temp Sensor Digital Serial (4-Wire, SPI, I2C) 16-Pin QSOP
ADT7519ARQ-REEL 制造商:Analog Devices 功能描述:Temp Sensor Digital Serial (4-Wire, SPI, I2C) 16-Pin QSOP T/R
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*