參數資料
型號: ADT7476AARQZ-R
廠商: ON Semiconductor
文件頁數: 58/66頁
文件大小: 945K
描述: IC REMOTE THERMAL CTLR 24QSOP
產品變化通告: MFG CHG Notification ADI to ON Semi
QSOP 24ld Pkg (MSL) Change 17/Jun/2010
標準包裝: 2,500
系列: dBCool®
功能: 風扇控制,溫度監控器
傳感器類型: 內部和外部
感應溫度: -40°C ~ 125°C
精確度: ±2.5%
拓撲: ADC,比較器,風扇速度計數器,多路復用器,寄存器庫
輸出類型: SMBus?
輸出警報:
輸出風扇:
電源電壓: 3 V ~ 3.6 V
工作溫度: -40°C ~ 125°C
安裝類型: 表面貼裝
封裝/外殼: 24-SSOP(0.154",3.90mm 寬)
供應商設備封裝: 24-QSOP
包裝: 帶卷 (TR)
其它名稱: ADT7476AARQZ-R-ND
ADT7476AARQZ-ROSTR
ADT7476A
http://onsemi.com
58
Table 69. PWM MINIMUM DUTY CYCLE REGISTERS (Note 1)
Register Address
R/W
Description
Power-On Default
0x64
R/W
PWM1 Minimum Duty Cycle
0x80 (50% Duty Cycle)
0x65
R/W
PWM2 Minimum Duty Cycle
0x80 (50% Duty Cycle)
0x66
R/W
PWM3 Minimum Duty Cycle
0x80 (50% Duty Cycle)
Bit No.
Name
R/W
Description
[7:0]
PWM Duty
Cycle
R/W
These bits define the PWM
MIN
 duty cycle for PWMx.
0x00 = 0% Duty Cycle (Fan Off)
0x40 = 25% Duty Cycle
0x80 = 50% Duty Cycle
0xFF = 100% Duty Cycle (Fan Full Speed)
1.  These registers become read-only when the ADT7476A is in automatic fan control mode.
Table 70. T
MIN
 REGISTERS (Note 1 and 2)
Register Address
R/W
Description
Power-On Default
0x67
R/W
Remote 1 Temperature T
MIN
0x5A (90癈)
0x68
R/W
Local Temperature T
MIN
0x5A (90癈)
0x69
R/W
Remote 2 Temperature T
MIN
0x5A (90癈)
1.  These are the T
MIN
 registers for each temperature channel. When the temperature measured exceeds T
MIN
, the appropriate fan runs at
minimum speed and increases with temperature according to T
RANGE
.
2.  These registers become read-only when the Configuration Register 1 Lock bit is set. Any further attempts to write to these registers have no
effect.
Table 71. THERM
 LIMIT REGISTERS (Note 1 and 2)
Register Address
R/W
Description
Power-On Default
0x6A
R/W
Remote 1 THERM
 Temperature Limit
0x64 (100癈)
0x6B
R/W
Local THERM
 Temperature Limit
0x64 (100癈)
0x6C
R/W
Remote 2 THERM
 Temperature Limit
0x64 (100癈)
1.  If any temperature measured exceeds its THERM
 limit, all PWM outputs drive their fans at 100% duty cycle. This is a fail-safe mechanism
incorporated to cool the system in the event of a critical overtemperature. It also ensures some level of cooling in the event that software
or hardware locks up. If set to 0x80, this feature is disabled. The PWM output remains at 100% until the temperature drops below
THERM
limit  hysteresis. If the THERM
 pin is programmed as an output, exceeding these limits by 0.25癈 can cause the THERM
 pin to
assert low as an output.
2.  These registers become read-only when the Configuration Register 1 Lock bit is set to 1. Any further attempts to write to these registers have
no effect.
Table 72. TEMPERATURE/T
MIN
 HYSTERESIS REGISTERS (Note 1 and 2)
Register Address
R/W
Description
Power-On Default
0x6D
[3:0]
[7:4]
R/W
HYSL
HYSR1
Remote 1 and local temperature hysteresis.
Local temperature hysteresis. 0癈 to 15癈 of hysteresis
can be applied to the local temperature AFC control
loops.
Remote 1 temperature hysteresis. 0癈 to 15癈 of hyster-
esis can be applied to the Remote 1 temperature AFC
control loops.
0x44
0x6E
R/W
HYSR2
Remote 2 temperature hysteresis.
Local temperature hysteresis. 0癈 to 15癈 of hysteresis
can be applied to the local temperature AFC control
loops.
0x40
1.  Each 4-bit value controls the amount of temperature hysteresis applied to a particular temperature channel. Once the temperature for that
channel falls below its T
MIN
value, the fan remains running at PWM
MIN
 duty cycle until the temperature = T
MIN
 hysteresis. Up to 15癈 of
hysteresis can be assigned to any temperature channel. The hysteresis value chosen also applies to that temperature channel if its THERM
limit is exceeded. The PWM output being controlled goes to 100% if the THERM
 limit is exceeded and remains at 100% until the temperature
drops below THERM
 hysteresis. For acoustic reasons, it is recommended that the hysteresis value not be programmed less than 4癈.
Setting the hysteresis value lower than 4癈 causes the fan to switch on and off regularly when the temperature is close to T
MIN
.
2.  These registers become read-only when the Configuration Register 1 Lock bit is set to 1. Any further attempts to write to these registers have
no effect.
相關PDF資料
PDF描述
ADT7481ARMZ-1RL IC SENSOR TEMP 2CH ALARM 10MSOP
ADT7482ARMZ-REEL IC SENSOR TEMP 2CH ALARM 10MSOP
ADT7485AARMZ-R IC TEMP/VOLT DGL SENS SST 10MSOP
ADT7486AARMZ-RL IC TEMP SENS DGTL 2CH SST 10MSOP
ADT7488AARMZ-RL IC TEMP/VOLT DGTL W/SST 10MSOP
相關代理商/技術參數
參數描述
ADT7476AARQZ-REEL 功能描述:IC REMOTE THERMAL CTRLR 24-QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:dBCool® 標準包裝:1 系列:- 功能:溫度監控系統(傳感器) 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C,外部傳感器 精確度:±2.5°C 本地(最大值),±5°C 遠程(最大值) 拓撲:ADC,比較器,寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6
ADT7476AARQZ-REEL7 功能描述:IC REMOTE THERMAL CTRLR 24-QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:dBCool® 標準包裝:1 系列:- 功能:溫度監控系統(傳感器) 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C,外部傳感器 精確度:±2.5°C 本地(最大值),±5°C 遠程(最大值) 拓撲:ADC,比較器,寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6
ADT7476AARQZ-RL7 功能描述:板上安裝溫度傳感器 MONITORS 5V/4 FANS RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
ADT7476ARQH 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:dBCOOL Remote Thermal Controller and Voltage Monitor
ADT7476ARQH-REEL 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:dBCOOL Remote Thermal Controller and Voltage Monitor