參數資料
型號： ADT7476AARQZ-R
廠商： ON Semiconductor
文件頁數： 26/66頁
文件大小： 945K
描述： IC REMOTE THERMAL CTLR 24QSOP
產品變化通告： MFG CHG Notification ADI to ON Semi
QSOP 24ld Pkg (MSL) Change 17/Jun/2010
標準包裝： 2,500
系列： dBCool®
功能： 風扇控制，溫度監控器
傳感器類型： 內部和外部
感應溫度： -40°C ~ 125°C
精確度： ±2.5%
拓?fù)洌?/td> ADC，比較器，風扇速度計數器，多路復用器，寄存器庫
輸出類型： SMBus?
輸出警報： 無
輸出風扇： 是
電源電壓： 3 V ~ 3.6 V
工作溫度： -40°C ~ 125°C
安裝類型： 表面貼裝
封裝/外殼： 24-SSOP（0.154"，3.90mm 寬）
供應商設備封裝： 24-QSOP
包裝： 帶卷 (TR)
其它名稱： ADT7476AARQZ-R-ND
ADT7476AARQZ-ROSTR
ADT7476A
http://onsemi.com
26
Figure 35 uses a 10 kW pullup resistor for the TACH
signal. This assumes that the TACH signal is an
open-collector from the fan. In all cases, the TACH signal
from the fan must be kept below 5.5 V maximum to prevent
damaging the ADT7476A.
Figure 36 shows a fan drive circuit using an NPN
transistor such as a general-purpose MMBT2222. While
these devices are inexpensive, they tend to have much lower
current handling capabilities and higher on resistance than
MOSFETs. When choosing a transistor, care should be taken
to ensure that it meets the fans current requirements. Ensure
that the base resistor is chosen so that the transistor is
saturated when the fan is powered on.
Because the fan drive circuitry in 4-wire fans is not
switched on or off, as with previous PWM driven/powered
fans, the internal drive circuit is always on and uses the
PWM input as a signal instead of a power supply. This
enables the internal fan drive circuit to perform better than
3-wire fans, especially for high frequency applications.
Figure 36. Driving a 3-wire Fan Using
an NPN Transistor
ADT7476A
TACH
PWM
Q1
MMBT2222
12 V
FAN
3.3 V
12 V
12 V
10 kW
4.7 kW
470 W
10 kW
TACH
Figure 37 shows a typical drive circuit for 4-wire fans.
Figure 37. Driving a 4-wire Fan
ADT7476A
TACH
PWM
12 V, 4-WIRE FAN
12 V
12 V
10 kW
4.7 kW
10 kW
TACH
V
CC
TACH
PWM
3.3 V
2 kW
Driving Two Fans from PWM3
The ADT7476A has four TACH inputs available for fan
speed measurement, but only three PWM drive outputs. If a
fourth fan is being used in the system, it should be driven
from the PWM3 output in parallel with the third fan.
Figure 38 shows how to drive two fans in parallel using low
cost NPN transistors. Figure 39 shows the equivalent circuit
using a MOSFET.
Because the MOSFET can handle up to 3.5 A, users can
connect another fan directly in parallel with the first. Care
should be taken in designing drive circuits with transistors
and FETs to ensure that the PWM outputs are not required
to source current, and that they sink less than the 5 mA
maximum current specified on the data sheet.
Driving up to Three Fans from PWM3
TACH measurements for fans are synchronized to
particular PWM channels; for example, TACH1 is
synchronized to PWM1. TACH3 and TACH4 are both
synchronized to PWM3, so PWM3 can drive two fans.
Alternatively, PWM3 can be programmed to synchronize
TACH2, TACH3, and TACH4 to the PWM3 output. This
allows PWM3 to drive two or three fans. In this case, the
drive circuitry looks the same, as shown in Figure 38 and
Figure 39. The SYNC bit in Register 0x62 enables this
function.
Synchronization is not required in high frequency mode
when used with 4-wire fans.
Table 34. SYNC: ENHANCE ACOUSTICS REGISTER 1
(REG. 0x62)
Bit
Mnemonic
Description
[4]
SYNC
1, Synchronizes TACH2, TACH3, and
TACH4 to PWM3.
Figure 38. Interfacing Two Fans in Parallel to the
PWM3 Output Using Low Cost NPN Transistors
ADT7476A
PWM3
Q1
MMBT3904
3.3 V
1 kW
TACH4
2.2 kW
3.3 V
TACH3
10 kW
10 kW
12 V
Q2
MMBT2222
Q3
MMBT2222
3.3 V
3.3 V
Figure 39. Interfacing Two Fans in Parallel to the
PWM3 Output Using a Single N-channel MOSFET
ADT7476A
TACH4
Q1
NDT3055L
3.3 V
10 kW
TYP
TACH3
PWM3
3.3 V
3.3 V
10 kW
TYP
10 kW
TYP
+V
+V
5 V
or
12 V
FAN
TACH
5 V
or
12 V
FAN
TACH
3.3 V
3.3 V
相關PDF資料
PDF描述
ADT7481ARMZ-1RL IC SENSOR TEMP 2CH ALARM 10MSOP
ADT7482ARMZ-REEL IC SENSOR TEMP 2CH ALARM 10MSOP
ADT7485AARMZ-R IC TEMP/VOLT DGL SENS SST 10MSOP
ADT7486AARMZ-RL IC TEMP SENS DGTL 2CH SST 10MSOP
ADT7488AARMZ-RL IC TEMP/VOLT DGTL W/SST 10MSOP
相關代理商/技術參數
參數描述
ADT7476AARQZ-REEL 功能描述:IC REMOTE THERMAL CTRLR 24-QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:dBCool® 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6
ADT7476AARQZ-REEL7 功能描述:IC REMOTE THERMAL CTRLR 24-QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:dBCool® 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6
ADT7476AARQZ-RL7 功能描述:板上安裝溫度傳感器 MONITORS 5V/4 FANS RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
ADT7476ARQH 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:dBCOOL Remote Thermal Controller and Voltage Monitor
ADT7476ARQH-REEL 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:dBCOOL Remote Thermal Controller and Voltage Monitor
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*