參數資料
型號： ADT7476AARQZ-R
廠商： ON Semiconductor
文件頁數： 12/66頁
文件大?。?/td> 945K
描述： IC REMOTE THERMAL CTLR 24QSOP
產品變化通告： MFG CHG Notification ADI to ON Semi
QSOP 24ld Pkg (MSL) Change 17/Jun/2010
標準包裝： 2,500
系列： dBCool®
功能： 風扇控制，溫度監控器
傳感器類型： 內部和外部
感應溫度： -40°C ~ 125°C
精確度： ±2.5%
拓?fù)洌?/td> ADC，比較器，風扇速度計數器，多路復用器，寄存器庫
輸出類型： SMBus?
輸出警報： 無
輸出風扇： 是
電源電壓： 3 V ~ 3.6 V
工作溫度： -40°C ~ 125°C
安裝類型： 表面貼裝
封裝/外殼： 24-SSOP（0.154"，3.90mm 寬）
供應商設備封裝： 24-QSOP
包裝： 帶卷 (TR)
其它名稱： ADT7476AARQZ-R-ND
ADT7476AARQZ-ROSTR
ADT7476A
http://onsemi.com
12
connected to a common SMBALERT
 line connected to the
master. If a devices SMBALERT
  line goes low, the
following procedure occurs:
1. SMBALERT
 is pulled low.
2. The master initiates a read operation and sends the
alert response address (ARA = 0001 100). This is
a general call address that must not be used as a
specific device address.
3. The device whose SMBALERT
 output is low
responds to the alert response address, and the
master reads its device address. The address of this
device is now known and can be interrogated per
usual.
4. If more than one devices SMBALERT
 output is
low, the one with the lowest device address has
priority in accordance with normal SMBus
arbitration.
5. Once the ADT7476A responds to the alert
response address, the master must read the status
registers, and SMBALERT
 is cleared only if the
error condition goes away.
SMBus Timeout
The ADT7476A includes an SMBus timeout feature. If
there is no SMBus activity for 35 ms, the ADT7476A
assumes the bus is locked and releases the bus. This prevents
the device from locking or holding the SMBus expecting
data. Some SMBus controllers cannot handle the SMBus
timeout feature, so if necessary, it can be disabled.
Table 6. CONFIGURATION REGISTER 1 (REG. 0x40)
Bit
Description
[6] TODIS
0: SMBus Timeout Enabled (Default)
1: SMBus Timeout Disabled
Virus Protection
To prevent rogue programs or viruses from accessing
critical ADT7476A register settings, the lock bit can be set.
Setting Bit 1 of Configuration Register 1 (0x40) sets the
lock bit and locks critical registers. In this mode, certain
registers can no longer be written to until the ADT7476A is
powered down and powered up again. For more information
on which registers are locked see Table 49.
Voltage Measurement Input
The ADT7476A has four external voltage measurement
channels. It can also measure its own supply voltage, V
CC
.
Pin 20 to Pin 23 can measure 5.0 V, 12 V, and 2.5 V
supplies, and the processor core voltage V
CCP
 (0 V to 3 V
input). The V
CC
 supply voltage measurement is carried out
through the V
CC
 pin (Pin 4). The 2.5 V input can be used to
monitor a chipset supply voltage in computer systems.
Analog-to-Digital Converter
All analog inputs are multiplexed into the on-chip,
successive-approximation,   analog-to-digital   converter,
which has a resolution of 10 bits. The basic input range is 0 V
to 2.25 V, but the inputs have built-in attenuators to allow
measurement of 2.5 V, 3.3 V, 5.0 V, 12 V, and the processor
core voltage V
CCP
 without any external components. To
allow the tolerance of these supply voltages, the ADC
produces an output of 3/4 full scale (768 dec or 300 hex) for
the nominal input voltage, giving it adequate headroom to
cope with overvoltages.
Input Circuitry
The internal structure for the analog inputs is shown in
Figure 24 The input circuit consists of an input protection
diode, an attenuator, plus a capacitor to form a first-order
low-pass filter that gives input immunity to high frequency
noise.
Figure 24. Structure of Analog Inputs
17.5 kW
52.5 kW
V
CCP
35 pF
45 kW
94 kW
+2.5V
IN
30 pF
68 kW
71 kW
V
CC
30 pF
93 kW
47 kW
+5V
IN
30 pF
183.6 kW
30 kW
+12V
IN
30 pF
MUX
Table 7. VOLTAGE MEASUREMENT REGISTERS
Register
Description
Default
0x20
2.5 V Reading
0x00
0x21
V
CCP
 Reading
0x00
0x22
V
CC
 Reading
0x00
0x23
5.0 V Reading
0x00
0x24
12 V Reading
0x00
Voltage Limit Registers
Associated with each voltage measurement channel is a
high and low limit register. Exceeding the programmed high
or low limit causes the appropriate status bit to be set.
Exceeding either limit can also generate SMBALERT
interrupts.
相關PDF資料
PDF描述
ADT7481ARMZ-1RL IC SENSOR TEMP 2CH ALARM 10MSOP
ADT7482ARMZ-REEL IC SENSOR TEMP 2CH ALARM 10MSOP
ADT7485AARMZ-R IC TEMP/VOLT DGL SENS SST 10MSOP
ADT7486AARMZ-RL IC TEMP SENS DGTL 2CH SST 10MSOP
ADT7488AARMZ-RL IC TEMP/VOLT DGTL W/SST 10MSOP
相關代理商/技術參數
參數描述
ADT7476AARQZ-REEL 功能描述:IC REMOTE THERMAL CTRLR 24-QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:dBCool® 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6
ADT7476AARQZ-REEL7 功能描述:IC REMOTE THERMAL CTRLR 24-QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:dBCool® 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6
ADT7476AARQZ-RL7 功能描述:板上安裝溫度傳感器 MONITORS 5V/4 FANS RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
ADT7476ARQH 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:dBCOOL Remote Thermal Controller and Voltage Monitor
ADT7476ARQH-REEL 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:dBCOOL Remote Thermal Controller and Voltage Monitor
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*