- 您現在的位置：買賣IC網 > PDF目錄9105 > ADF4150HVBCPZ-RL7 (Analog Devices Inc)IC FRACTION-N FREQ SYNTH 32LFCSP PDF資料下載
參數資料
| 型號： | ADF4150HVBCPZ-RL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 18/28頁 |
| 文件大小： | 0K |
| 描述： | IC FRACTION-N FREQ SYNTH 32LFCSP |
| 標準包裝： | 1,500 |
| 類型： | * |
| PLL： | 是 |
| 輸入： | CMOS |
| 輸出： | 時鐘 |
| 電路數： | 1 |
| 比率 - 輸入:輸出： | 1:2 |
| 差分 - 輸入:輸出： | 無/是 |
| 頻率 - 最大： | 3GHz |
| 除法器/乘法器： | 是/無 |
| 電源電壓： | 3 V ~ 3.6 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-WFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 32-LFCSP-WQ（5x5） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
ADF4150HV
Rev. 0 | Page 25 of 28
INTERFACING TO THE ADuC702x AND
THE ADSP-BF527
The ADF4150HV has a simple SPI-compatible serial interface for
writing to the device. The CLK, DATA, and LE pins control the
data transfer. When LE goes high, the 32 bits that were clocked
into the appropriate register on each rising edge of CLK are
transferred to the appropriate latch. See Figure 2 for the timing
diagram and Table 6 for the register address table.
ADuC702x Interface
family is based on an ARM7 core, but the same interface can be
used with any 8051-based microcontroller.
The microcontroller is set up for SPI master mode with CPHA =
0. To initiate the operation, the I/O port driving LE is brought
low. Each latch of the ADF4150HV needs a 32-bit word, which
is accomplished by writing four 8-bit bytes from the micro-
controller to the device. After the fourth byte is written, the
LE input should be brought high to complete the transfer.
ADuC702x
ADF4150HV
CLK
DATA
LE
CE
MUXOUT
(LOCK DETECT)
SCLOCK
MOSI
I/O PORTS
09
05
8-
03
0
I/O port lines on the ADuC702x are also used to control the
power-down input (CE) and the lock detect (MUXOUT con-
figured for lock detect and polled by the port input). When
operating in the mode described, the maximum SPI transfer
rate of the ADuC7023 is 20 Mbps. This means that the maxi-
mum rate at which the output frequency can be changed is
833 kHz. If using a faster SPI clock, make sure that the SPI
timing requirements listed in Table 2 are adhered to.
Blackfin ADSP-BF527 Interface
the Blackfin ADSP-BF527 digital signal processor (DSP). The
ADF4150HV needs a 32-bit serial word for each latch write.
The easiest way to accomplish this using the Blackfin family
is to use the autobuffered transmit mode of operation with
alternate framing. This mode provides a means for transmitting
an entire block of serial data before an interrupt is generated.
ADSP-BF527
ADF4150HV
CLK
DATA
LE
CE
MUXOUT
(LOCK DETECT)
SCK
MOSI
GPIO
I/O PORTS
09
05
8-
03
1
Figure 32. ADSP-BF527 to ADF4150HV Interface
Set up the word length for eight bits and use four memory loca-
tions for each 32-bit word. To program each 32-bit latch, store
the 8-bit bytes, enable the autobuffered mode, and write to the
transmit register of the DSP. This last operation initiates the
autobuffer transfer. If using a faster SPI clock, make sure that
the SPI timing requirements listed in Table 2 are adhered to.
PCB DESIGN GUIDELINES FOR A CHIP SCALE
PACKAGE
The lands on the chip scale package (CP-32-11) are rectangular.
The PCB pad for these lands must be 0.1 mm longer than the
package land length and 0.05 mm wider than the package land
width. Each land must be centered on the pad to ensure that the
solder joint size is maximized.
The bottom of the chip scale package has a central exposed
thermal pad. The thermal pad on the PCB must be at least as
large as the exposed pad. On the PCB, there must be a minimum
clearance of 0.25 mm between the thermal pad and the inner
edges of the pad pattern to ensure that shorting is avoided.
Thermal vias can be used on the PCB thermal pad to improve
the thermal performance of the package. If vias are used, they
must be incorporated into the thermal pad at 1.2 mm pitch grid.
The via diameter must be between 0.3 mm and 0.33 mm, and
the via barrel must be plated with 1 oz. of copper to plug the via.
相關PDF資料 |
PDF描述 |
|---|---|
| VI-27Y-MY-F1 | CONVERTER MOD DC/DC 3.3V 33W |
| X9315WST1 | IC XDCP 32-TAP 10K 3WIRE 8-SOIC |
| VI-27Y-MX-F4 | CONVERTER MOD DC/DC 3.3V 49.5W |
| VI-242-IV | CONVERTER MOD DC/DC 15V 150W |
| ADF4154BRU-REEL | IC FRACTION-N FREQ SYNTH 16TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADF4151 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Fractional-N/Integer-N PLL Synthesizer |
| ADF4151BCPZ | 功能描述:IC PLL FREQ SYNTHESIZER 32LFCSP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:1,000 系列:Precision Edge® 類型:時鐘/頻率合成器 PLL:無 輸入:CML，PECL 輸出:CML 電路數:1 比率 - 輸入:輸出:2:1 差分 - 輸入:輸出:是/是 頻率 - 最大:10.7GHz 除法器/乘法器:無/無 電源電壓:2.375 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-VFQFN 裸露焊盤，16-MLF? 供應商設備封裝:16-MLF?（3x3） 包裝:帶卷 (TR) 其它名稱:SY58052UMGTRSY58052UMGTR-ND |
| ADF4151BCPZ-RL7 | 功能描述:IC FRACTION-N FREQ SYNTH 32LFCSP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:1,000 系列:Precision Edge® 類型:時鐘/頻率合成器 PLL:無 輸入:CML，PECL 輸出:CML 電路數:1 比率 - 輸入:輸出:2:1 差分 - 輸入:輸出:是/是 頻率 - 最大:10.7GHz 除法器/乘法器:無/無 電源電壓:2.375 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-VFQFN 裸露焊盤，16-MLF? 供應商設備封裝:16-MLF?（3x3） 包裝:帶卷 (TR) 其它名稱:SY58052UMGTRSY58052UMGTR-ND |
| ADF4152HVBCPZ | 功能描述:IC FRACTION-N FREQ SYNTH 32LFCSP 制造商:analog devices inc. 系列:- 包裝:托盤 零件狀態:在售 類型:* PLL:是 輸入:CMOS 輸出:時鐘 電路數:1 比率 - 輸入:輸出:2:2 差分 - 輸入:輸出:是/無 頻率 - 最大值:5GHz 分頻器/倍頻器:是/是 電壓 - 電源:3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:32-VFQFN 裸露焊盤，CSP 供應商器件封裝:32-LFCSP-VQ（5x5） 標準包裝:1 |
| ADF4152HVBCPZ-RL7 | 功能描述:IC FRACTION-N FREQ SYNTH 32LFCSP 制造商:analog devices inc. 系列:- 包裝:剪切帶（CT） 零件狀態:在售 類型:* PLL:是 輸入:CMOS 輸出:時鐘 電路數:1 比率 - 輸入:輸出:2:2 差分 - 輸入:輸出:是/無 頻率 - 最大值:5GHz 分頻器/倍頻器:是/是 電壓 - 電源:3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:32-VFQFN 裸露焊盤，CSP 供應商器件封裝:32-LFCSP-VQ（5x5） 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。