By default, the ADAU1781 is in I2C mode, but c" />
參數資料
型號： ADAU1781BCPZ-RL7
廠商： Analog Devices Inc
文件頁數： 30/92頁
文件大?。?/td> 0K
描述： IC SIGMADSP CODEC LN 32LFCSP
標準包裝： 1,500
系列： SigmaDSP®
類型： 立體聲音頻
數據接口： I²C，串行，SPI?
分辨率（位）： 24 b
ADC / DAC 數量： 2 / 2
三角積分調變： 無
S/N 比，標準 ADC / DAC (db)： 100 / 105（差分），100 / 103（單端）
動態范圍，標準 ADC / DAC (db)： 99.2 / 105（差分），99.2 / 103（單端）
電壓 - 電源，模擬： 1.8 V ~ 3.65 V
電壓 - 電源，數字： 1.63 V ~ 3.65 V
工作溫度： -25°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 32-VFQFN 裸露焊盤，CSP
供應商設備封裝： 32-LFCSP-VQ
包裝： 帶卷 (TR)
ADAU1781
Rev. B | Page 36 of 92
SPI PORT
By default, the ADAU1781 is in I2C mode, but can be put into SPI
control mode by pulling CLATCH low three times. The SPI port
uses a 4-wire interface, consisting of CLATCH, CCLK, CDATA,
and COUT signals, and is always a slave port. The CLATCH
Chip Address R/
signal
goes low at the beginning of a transaction and high at the end of
a transaction. The CCLK signal latches CDATA on a low-to-high
transition. COUT data is shifted out of the ADAU1781 on the
falling edge of CCLK and should be clocked into a receiving
device, such as a microcontroller, on the CCLK rising edge. The
CDATA signal carries the serial input data, and the COUT signal is
the serial output data. The COUT signal remains three-stated until
a read operation is requested. This allows other SPI-compatible
peripherals to share the same readback line. All SPI transactions
have the same basic format shown in Table 24. A timing diagram
is shown in Figure 4. All data should be written MSB first. The
ADAU1781 can be taken out of SPI mode only by a full reset.
W
The first byte of an SPI transaction includes the 7-bit chip address
and an R/W
Table 23. SPI Address Byte Format
bit. The chip address is always 0x38. The LSB of
this first byte determines whether the SPI transaction is a read
(Logic 1) or a write (Logic 0).
Bit 0
Bit 1
Bit 2
Bit 3
Bit 4
Bit 5
Bit 6
Bit 7
0
R/W
Subaddress
The 12-bit subaddress word is decoded into a location in one of
the registers. This subaddress is the location of the appropriate
register. The MSBs of the subaddress are zero-padded to bring the
word to a full 2-byte length.
Data Bytes
The number of data bytes varies according to the register being
accessed. During a burst mode write, an initial subaddress is
written followed by a continuous sequence of data for consecutive
register locations. A sample timing diagram for a single-write
SPI operation to the parameter memory is shown in Figure 43.
A sample timing diagram of a single-read SPI operation is shown in
Figure 44. The COUT pin goes from three-state to being driven at
the beginning of Byte 3. In this example, Byte 0 to Byte 2 contain
the addresses and R/W
SPI Read/Write Clock Frequency (CCLK)
bit, and subsequent bytes carry the data.
The SPI port of the ADAU1781 has asymmetrical read and
write clock frequencies. It is possible to write data into the
device at higher data rates than reading data out of the device.
More detailed information is available in the Digital Timing
MEMORY AND REGISTER ACCESS
Several conditions must be true to have full access to all memory
and registers via the control port:
The ADAU1781 must have finished its initialization,
including power-on reset, PLL lock, and self-boot.
The core clock must be enabled (Register 16384 (0x4000),
clock control, Bit 0, core clock enable, set to 1).
The memory controller must be powered (Register 16512
(0x4080), Digital Power-Down 0, Bit 6, memory controller,
set to 1).
The SigmaDSP core must be powered (Register 16512
(0x4080), Digital Power-Down 0, Bit 0, SigmaDSP core,
set to 1).
Table 24. Generic Control Word Format
Byte 0
Byte 1
Byte 2
Byte 3
Byte 41
CHIP_ADR[6:0], R/W
SUBADR[15:8]
SUBADR[7:0]
Data
1 Continues to end of data.
相關PDF資料
PDF描述
ADAU1961WBCPZ-R7 IC STEREO AUD CODEC LP 32LFCSP
ADAU1966WBSTZ IC DAC 24BIT SPI/I2C 192K 80LQFP
ADAV801ASTZ-REEL IC CODEC AUDIO R-DVD 3.3V 64LQFP
ADAV803ASTZ IC CODEC AUDIO R-DVD 3.3V 64LQFP
ADDAC80-CBI-V IC DAC 12BIT LOW COST 24-CDIP
相關代理商/技術參數
參數描述
ADAU1961 制造商:AD 制造商全稱:Analog Devices 功能描述:Stereo, Low Power, 96 kHz, 24-Bit Audio Codec with Integrated PLL
ADAU1961WBCPZ 功能描述:IC STEREO AUD CODEC LP 32LFCSP RoHS:是 類別:集成電路 (IC) >> 接口 - 編解碼器 系列:- 標準包裝:2,500 系列:- 類型:PCM 數據接口:PCM 音頻接口 分辨率（位）:15 b ADC / DAC 數量:1 / 1 三角積分調變:是 S/N 比，標準 ADC / DAC (db):- 動態范圍，標準 ADC / DAC (db):- 電壓 - 電源，模擬:2.7 V ~ 3.3 V 電壓 - 電源，數字:2.7 V ~ 3.3 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-VFBGA 供應商設備封裝:80-BGA MICROSTAR JUNIOR（5x5） 包裝:帶卷 (TR) 其它名稱:296-21257-2
ADAU1961WBCPZ-R7 功能描述:IC STEREO AUD CODEC LP 32LFCSP RoHS:是 類別:集成電路 (IC) >> 接口 - 編解碼器 系列:- 標準包裝:2,500 系列:- 類型:立體聲音頻 數據接口:串行 分辨率（位）:18 b ADC / DAC 數量:2 / 2 三角積分調變:是 S/N 比，標準 ADC / DAC (db):81.5 / 88 動態范圍，標準 ADC / DAC (db):82 / 87.5 電壓 - 電源，模擬:2.6 V ~ 3.3 V 電壓 - 電源，數字:1.7 V ~ 3.3 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-WFQFN 裸露焊盤 供應商設備封裝:48-TQFN-EP（7x7） 包裝:帶卷 (TR)
ADAU1961WBCPZ-RL 功能描述:IC STEREO AUD CODEC LP 32LFCSP RoHS:是 類別:集成電路 (IC) >> 接口 - 編解碼器 系列:- 標準包裝:2,500 系列:- 類型:立體聲音頻 數據接口:串行 分辨率（位）:18 b ADC / DAC 數量:2 / 2 三角積分調變:是 S/N 比，標準 ADC / DAC (db):81.5 / 88 動態范圍，標準 ADC / DAC (db):82 / 87.5 電壓 - 電源，模擬:2.6 V ~ 3.3 V 電壓 - 電源，數字:1.7 V ~ 3.3 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-WFQFN 裸露焊盤 供應商設備封裝:48-TQFN-EP（7x7） 包裝:帶卷 (TR)
ADAU1962AWBSTZ 制造商:Analog Devices 功能描述:AUTOMOTIVE HIGH PERFORMANCE 12 DAC - Trays 制造商:Analog Devices 功能描述:IC DAC 80LQFP 制造商:Analog Devices 功能描述:DAC 24 BITS 48KHZ SPI LQFP 制造商:Analog Devices 功能描述:DAC, 24BIT, 192KSPS, LQFP-80, Resolution (Bits):24bit, Sampling Rate:192kSPS, Input Channel Type:Differential, Single Ended, Supply Voltage Range:3.14V to 3.46V, Digital IC Case Style:LQFP, No. of Pins:80, Data Interface:I2C, SPI
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*