- 您現在的位置：買賣IC網 > PDF目錄1894 > AD9887AKSZ-100 (Analog Devices Inc)IC INTRFACE ANALOG/DVI 160-MQFP PDF資料下載
參數資料
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
REV. 0
AD9887
–31–
When DEMUX = 0, this bit is ignored as data always
comes out of only Port A.
0E
4
HSYNC Output Polarity
One bit that determines the polarity of the HSYNC out-
put and the SOG output. Table XV shows the effect of
this option. SYNC indicates the logic state of the sync pulse.
Table XV. HSYNC Output Polarity Settings
Setting
SYNC
0
Logic 1 (Positive Polarity)
1
Logic 0 (Negative Polarity)
The default setting for this register is 1. (This option
works on both the analog and digital interfaces.)
0E
3
VSYNC Output Invert
One bit that inverts the polarity of the VSYNC output.
Table XVI shows the effect of this option.
Table XVI. VSYNC Output Polarity Settings
Setting
VSYNC Output
0
Invert
1
No Invert
The default setting for this register is 1. (This option
works on both the analog and digital interfaces.)
0F
7
HSYNC Input Polarity
A bit that must be set to indicate the polarity of the HSYNC
signal that is applied to the PLL HSYNC input.
Table XVII. HSYNC Input Polarity Settings
HSPOL
Function
0
Active LOW
1
Active HIGH
Active LOW is the traditional negative-going Hsync pulse.
All timing is based on the leading edge of Hsync, which is
the FALLING edge. The rising edge has no effect.
Active HIGH is inverted from the traditional Hsync, with a
positive-going pulse. This means that timing will be based on
the leading edge of Hsync, which is now the RISING edge.
The device will operate if this bit is set incorrectly, but the
internally generated clamp position, as established by
CLPOS, will not be placed as expected, which may gener-
ate clamping errors.
The power-up default value is HSPOL = 1.
0F
6 COAST Input Polarity
A bit to indicate the polarity of the COAST signal that is
applied to the PLL COAST input.
Table XVIII. COAST Input Polarity Settings
CSTPOL
Function
0
Active LOW
1
Active HIGH
Active LOW means that the clock generator will ignore Hsync
inputs when COAST is LOW, and continue operating at the
same nominal frequency until COAST goes HIGH.
Active HIGH means that the clock generator will ignore
Hsync inputs when COAST is HIGH, and continue operat-
ing at the same nominal frequency until COAST goes LOW.
This function needs to be used along with the COAST
polarity override bit (Register 14, Bit 1).
The power-up default value is CSTPOL = 1.
0F
5 Clamp Input Signal Source
A bit that determines the source of clamp timing.
Table XIX. Clamp Input Signal Source Settings
EXTCLMP
Function
0
Internally-Generated Clamp
1
Externally-Provided Clamp Signal
A 0 enables the clamp timing circuitry controlled by
CLPLACE and CLDUR. The clamp position and dura-
tion is counted from the leading edge of Hsync.
A 1 enables the external CLAMP input pin. The three
channels are clamped when the CLAMP signal is
active. The polarity of CLAMP is determined by the
CLAMPOL bit.
The power-up default value is EXTCLMP = 0.
0F
4
CLAMP Input Signal Polarity
A bit that determines the polarity of the externally pro-
vided CLAMP signal.
Table XX. CLAMP Input Signal Polarity Settings
EXTCLMP
Function
0
Active LOW
1
Active HIGH
A Logic 0 means that the circuit will clamp when CLAMP
is HIGH, and it will pass the signal to the ADC when
CLAMP is LOW.
A Logic 1 means that the circuit will clamp when CLAMP
is LOW, and it will pass the signal to the ADC when
CLAMP is HIGH.
The power-up default value is CLAMPOL = 1.
0F
3 External Clock Select
A bit that determines the source of the pixel clock.
Table XXI. External Clock Select Settings
EXTCLK
Function
0
Internally Generated Clock
1
Externally Provided Clock Signal
A Logic 0 enables the internal PLL that generates the
pixel clock from an externally provided Hsync.
OBSOLETE
相關PDF資料 |
PDF描述 |
|---|---|
| AD9887AKSZ-140 | IC INTRFACE ANALOG/DVI 160-MQFP |
| AD9888KSZ-170 | IC ANALOG INTRFC 170MSPS 128MQFP |
| AD9895KBCZRL | IC CCD SIGNAL PROC/GEN 64-CSPBGA |
| AD9910BSVZ-REEL | IC DDS 1GSPS 14BIT PAR 100TQFP |
| AD9911BCPZ-REEL7 | IC DDS 500MSPS DAC 10BIT 56LFCSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9887AKSZ-1001 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual Interface for Flat Panel Display |
| AD9887AKSZ-140 | 功能描述:IC INTRFACE ANALOG/DVI 160-MQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 特色產品:NXP - I2C Interface 標準包裝:1 系列:- 應用:2 通道 I²C 多路復用器 接口:I²C，SM 總線 電源電壓:2.3 V ~ 5.5 V 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:剪切帶 (CT) 安裝類型:表面貼裝 產品目錄頁面:825 (CN2011-ZH PDF) 其它名稱:568-1854-1 |
| AD9887AKSZ-1401 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual Interface for Flat Panel Display |
| AD9887AKSZ-170 | 功能描述:IC INTRFACE ANALOG/DVI 160-MQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 特色產品:NXP - I2C Interface 標準包裝:1 系列:- 應用:2 通道 I²C 多路復用器 接口:I²C，SM 總線 電源電壓:2.3 V ~ 5.5 V 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:剪切帶 (CT) 安裝類型:表面貼裝 產品目錄頁面:825 (CN2011-ZH PDF) 其它名稱:568-1854-1 |
| AD9887AKSZ-170 | 制造商:Analog Devices 功能描述:IC DUAL DISPLAY INTERFACE |
發布緊急采購，3分鐘左右您將得到回復。