- 您現在的位置：買賣IC網 > PDF目錄1894 > AD9887AKSZ-100 (Analog Devices Inc)IC INTRFACE ANALOG/DVI 160-MQFP PDF資料下載
參數資料
| 型號： | AD9887AKSZ-100 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 10/40頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC INTRFACE ANALOG/DVI 160-MQFP |
| 標準包裝： | 24 |
| 應用： | 圖形卡，VGA 接口 |
| 接口： | 模擬和數字 |
| 電源電壓： | 3.15 V ~ 3.45 V |
| 封裝/外殼： | 160-BQFP |
| 供應商設備封裝： | 160-MQFP（28x28） |
| 包裝： | 托盤 |
| 安裝類型： | 表面貼裝 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
REV. 0
–18–
AD9887
E2
Figure 14. Even Pixels from Frame 2
O1E2O1E2O1E2O1E2O1E2O1E2
Figure 15. Combine Frame Output from Graphics Controller
O3E2O3E2O3E2O3E2O3E2O3E2
Figure 16. Subsequent Frame from Controller
Timing (Analog Interface)
The following timing diagrams show the operation of the
AD9887 analog interface in all clock modes. The part estab-
lishes timing by having the sample that corresponds to the pixel
digitized when the leading edge of HSYNC occurs sent to the
“A” data port. In Dual Channel Mode, the next sample is sent
to the “B” port. Future samples are alternated between the “A”
and “B” data ports. In Single Channel Mode, data is only sent
to the “A” data port, and the “B” port is placed in a high
impedance state.
The Output Data Clock signal is created so that its rising edge
always occurs between “A” data transitions, and can be used to
latch the output data externally.
PXLCLK
ANY OUTPUT
SIGNAL
DATACK
(OUTPUT)
tSKEW
tDCYCLE
tPER
DATA OUT
Figure 17. Analog Output Timing
Hsync Timing
Horizontal sync is processed in the AD9887 to eliminate
ambiguity in the timing of the leading edge with respect to the
phase-delayed pixel clock and data.
The Hsync input is used as a reference to generate the pixel
sampling clock. The sampling phase can be adjusted, with respect
to Hsync, through a full 360
° in 32 steps via the Phase Adjust
register (to optimize the pixel sampling time). Display systems use
Hsync to align memory and display write cycles, so it is important
to have a stable timing relationship between Hsync output
(HSOUT) and data clock (DATACK).
Three things happen to Horizontal Sync in the AD9887. First,
the polarity of Hsync input is determined and will thus have a
known output polarity. The known output polarity can be pro-
grammed either active high or active low (Register 04H, Bit 4).
Second, HSOUT is aligned with DATACK and data outputs.
Third, the duration of HSOUT (in pixel clocks) is set via Regis-
ter 07H. HSOUT is the sync signal that should be used to drive
the rest of the display system.
Coast Timing
In most computer systems, the Hsync signal is provided con-
tinuously on a dedicated wire. In these systems, the COAST
input and function are unnecessary, and should not be used.
In some systems, however, Hsync is disturbed during the Verti-
cal Sync period (Vsync). In some cases, Hsync pulses disappear.
In other systems, such as those that employ Composite Sync
(Csync) signals or embed Sync-On-Green (SOG), Hsync includes
equalization pulses or other distortions during Vsync. To avoid
upsetting the clock generator during Vsync, it is important to
ignore these distortions. If the pixel clock PLL sees extraneous
pulses, it will attempt to lock to this new frequency, and will
have changed frequency by the end of the Vsync period. It will
then take a few lines of correct Hsync timing to recover at the
beginning of a new frame, resulting in a “tearing” of the image
at the top of the display.
The COAST input is provided to eliminate this problem. It is
an asynchronous input that disables the PLL input and allows
the clock to free-run at its then-current frequency. The PLL can
free-run for several lines without signicant frequency drift.
Coast can be provided by the graphics controller or it can be
internally generated by the AD9887 Sync processing engine.
OBSOLETE
相關PDF資料 |
PDF描述 |
|---|---|
| AD9887AKSZ-140 | IC INTRFACE ANALOG/DVI 160-MQFP |
| AD9888KSZ-170 | IC ANALOG INTRFC 170MSPS 128MQFP |
| AD9895KBCZRL | IC CCD SIGNAL PROC/GEN 64-CSPBGA |
| AD9910BSVZ-REEL | IC DDS 1GSPS 14BIT PAR 100TQFP |
| AD9911BCPZ-REEL7 | IC DDS 500MSPS DAC 10BIT 56LFCSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9887AKSZ-1001 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual Interface for Flat Panel Display |
| AD9887AKSZ-140 | 功能描述:IC INTRFACE ANALOG/DVI 160-MQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 特色產品:NXP - I2C Interface 標準包裝:1 系列:- 應用:2 通道 I²C 多路復用器 接口:I²C，SM 總線 電源電壓:2.3 V ~ 5.5 V 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:剪切帶 (CT) 安裝類型:表面貼裝 產品目錄頁面:825 (CN2011-ZH PDF) 其它名稱:568-1854-1 |
| AD9887AKSZ-1401 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual Interface for Flat Panel Display |
| AD9887AKSZ-170 | 功能描述:IC INTRFACE ANALOG/DVI 160-MQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 特色產品:NXP - I2C Interface 標準包裝:1 系列:- 應用:2 通道 I²C 多路復用器 接口:I²C，SM 總線 電源電壓:2.3 V ~ 5.5 V 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:剪切帶 (CT) 安裝類型:表面貼裝 產品目錄頁面:825 (CN2011-ZH PDF) 其它名稱:568-1854-1 |
| AD9887AKSZ-170 | 制造商:Analog Devices 功能描述:IC DUAL DISPLAY INTERFACE |
發布緊急采購，3分鐘左右您將得到回復。