- 您現在的位置：買賣IC網 > PDF目錄1980 > AD7298-1BCPZ-RL (Analog Devices Inc)IC ADC 10BIT SPI/SRL 8CH 20LFCSP PDF資料下載
參數資料
| 型號： | AD7298-1BCPZ-RL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 10/25頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 10BIT SPI/SRL 8CH 20LFCSP |
| 標準包裝： | 1 |
| 位數： | 10 |
| 采樣率（每秒）： | 1M |
| 數據接口： | DSP，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 23mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-WFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 20-LFCSP-WQ（4x4） |
| 包裝： | 標準包裝 |
| 輸入數目和類型： | 8 個單端，單極 |
| 其它名稱： | AD7298-1BCPZ-RLDKR |
AD7298-1
Rev. A | Page 17 of 24
CS
SCLK
DOUT
DIN
1
10
16
1
16
1
16
CONVERSION RESULT
FOR CHANNEL 0
CONVERSION RESULT
FOR CHANNEL 1
INVALID DATA
NO WRITE TO THE
CONTROL REGISTER
NO WRITE TO THE
CONTROL REGISTER
DATA WRITTEN TO CONTROL
REGISTER CH0, CH1, AND CH2
SELECTED: REPEAT = 1
CS
SCLK
DOUT
DIN
1
16
1
16
1
16
CONVERSION RESULT
FOR CHANNEL 0
CONVERSION RESULT
FOR CHANNEL 2
NO WRITE TO THE
CONTROL REGISTER
NO WRITE TO THE
CONTROL REGISTER
NO WRITE TO THE
CONTROL REGISTER
09321-
0
1
Figure 25. Configuring a Conversion and Read in Repeat Mode
REPEAT OPERATION
The REPEAT bit in the control register allows the user to select
a sequence of channels on which the AD7298-1 continuously
converts. When the REPEAT bit is set in the control register, the
AD7298-1 continuously cycles through the selected channels in
ascending order, beginning with the lowest channel and converting
all channels selected in the control register. On completion of
the sequence, the AD7298-1 returns to the first selected channel
in the control register and recommences the sequence.
The conversion sequence of the selected channels in the repeat
mode of operation continues until the control register of the
AD7298-1 is reprogrammed. It is not necessary to write to the
control register once a repeat operation is initiated unless a change
in the AD7298-1 configuration is required. The WRITE bit
must be set to zero, or the DIN line tied low to ensure that the
control register is not accidentally overwritten or the automatic
conversion sequence interrupted.
A write to the control register during the repeat mode of operation
resets the cycle even if the selected channels are unchanged.
Thus, the next conversion by the AD7298-1 after a write
operation will be the first selected channel in the sequence.
To select a sequence of channels, the associated channel bit
must be set to a logic high state (1) for each analog input whose
conversion is required. For example, if the REPEAT bit = 1, then
CH0, CH1, and CH2 = 1. The VIN0 analog input is converted on
the first CS falling edge following the write to the control register,
the VIN1 channel is converted on the subsequent CS falling edge,
and the VIN0 conversion result is available for reading. The third
CS falling edge following the write operation initiates a conversion
on VIN2 and has the VIN1 result available for reading. The AD7298-1
operates with one cycle latency, therefore the conversion result
corresponding to each conversion is available one serial read
cycle after the cycle in which the conversion is initiated.
This mode of operation simplifies the operation of the device by
allowing consecutive channels to be converted without having
to reprogram the control register or write to the part on each
serial transfer. Figure 25 illustrates how to set up the AD7298-1
to continuously convert on a particular sequence of channels.
To exit the repeat mode of operation and revert to the traditional
mode of operation of a multichannel ADC, ensure that the
REPEAT bit = 0 on the next serial write.
相關PDF資料 |
PDF描述 |
|---|---|
| AD7298BCPZ-RL7 | IC ADC 10BIT SPI/SRL 8CH 20LFCSP |
| AD7302BRUZ-REEL7 | IC DAC 8BIT DUAL R-R 20-TSSOP |
| AD7303BRM | IC DAC 8BIT DUAL R-R 8-MSOP |
| AD7305BRU | IC DAC 8BIT QUAD R-R 20-TSSOP |
| AD7321BRUZ-REEL7 | IC ADC 12BIT+ SAR 2CHAN 14TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7298BCPZ | 功能描述:IC ADC 12BIT SPI/SRL 1M 20LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD7298BCPZ-RL7 | 功能描述:IC ADC 10BIT SPI/SRL 8CH 20LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| AD73 | 制造商:Distributed By MCM 功能描述:REFRIGERATR DOOR GASKET DIRECT |
| AD7302 | 制造商:AD 制造商全稱:Analog Devices 功能描述:2.7 V to 5.5 V, Parallel Input Dual Voltage Output 8-Bit DAC |
| AD7302BN | 功能描述:IC DAC 8BIT DUAL R-R 20-DIP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:2,400 系列:- 設置時間:- 位數:18 數據接口:串行 轉換器數目:3 電壓電源:模擬和數字 功率耗散（最大）:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:36-TFBGA 供應商設備封裝:36-TFBGA 包裝:帶卷 (TR) 輸出數目和類型:* 采樣率（每秒）:* |
發布緊急采購，3分鐘左右您將得到回復。