- 您現在的位置：買賣IC網 > PDF目錄1980 > AD7190BRUZ-REEL (Analog Devices Inc)IC ADC 2CH 24BIT W/PGA 24TSSOP PDF資料下載
參數資料
| 型號： | AD7190BRUZ-REEL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 15/41頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 2CH 24BIT W/PGA 24TSSOP |
| 設計資源： | Precision Weigh Scale Design Using AD7190 with Internal PGA (CN0102) |
| 標準包裝： | 2,500 |
| 位數： | 24 |
| 采樣率（每秒）： | 4.8k |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 105°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 24-TSSOP |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 2 個差分，雙極；4 個偽差分，雙極 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁
Data Sheet
AD7190
Rev. C | Page 21 of 40
Table 17. Mode Register Bit Designations
Bit Location
Bit Name
Description
MR23 to MR21
MD2 to MD0
Mode select bits. These bits select the operating mode of the AD7190 (see Table 18).
MR20
DAT_STA
This bit enables the transmission of status register contents after each data register read. When
DAT_STA is set, the contents of the status register are transmitted along with each data register read.
This function is useful when several channels are selected because the status register identifies the
channel to which the data register value corresponds.
MR19 to MR18
CLK1 to CLK0
These bits are used to select the clock source for the AD7190. Either the on-chip 4.92 MHz clock or an
external clock can be used. The ability to use an external clock allows several AD7190 devices to be
synchronized. Also, 50 Hz/60 Hz rejection is improved when an accurate external clock drives the
AD7190.
CLK1
CLK0
ADC Clock Source
0
External crystal. The external crystal is connected from MCLK1 to MCLK2.
0
1
External clock. The external clock is applied to the MCLK2 pin.
1
0
Internal 4.92 MHz clock. Pin MCLK2 is tristated.
1
Internal 4.92 MHz clock. The internal clock is available on MCLK2.
MR17 to MR16
These bits must be programmed with a Logic 0 for correct operation.
MR15
SINC3
Sinc3 filter select bit. When this bit is cleared, the sinc4 filter is used (default value). When this bit is set,
the sinc3 filter is used. The benefit of the sinc3 filter compared to the sinc4 filter is its lower settling time
when chop is disabled. For a given output data rate, fADC, the sinc3 filter has a settling time of 3/fADC
while the sinc4 filter has a settling time of 4/fADC. The sinc4 filter, due to its deeper notches, gives better
50 Hz/60 Hz rejection. At low output data rates, both filters give similar rms noise and similar no
missing codes for a given output data rate. At higher output data rates (FS values less than 5), the sinc4
filter gives better performance than the sinc3 filter for rms noise and no missing codes.
MR14
This bit must be programmed with a Logic 0 for correct operation.
MR13
ENPAR
Enable parity bit. When ENPAR is set, parity checking on the data register is enabled. The DAT_STA bit
in the mode register should be set when the parity check is used. When the DAT_STA bit is set, the
contents of the status register are transmitted along with the data for each data register read.
MR12
This bit must be programmed with a Logic 0 for correct operation.
MR11
Single
Single cycle conversion enable bit. When this bit is set, the AD7190 settles in one conversion cycle so
that it functions as a zero latency ADC. This bit has no affect when multiple analog input channels are
enabled or when the single conversion mode is selected.
MR10
REJ60
This bit enables a notch at 60 Hz when the first notch of the sinc filter is at 50 Hz. When REJ60 is set, a
filter notch is placed at 60 Hz when the sinc filter first notch is at 50 Hz. This allows simultaneous
50 Hz/60 Hz rejection.
MR9 to MR0
FS9 to FS0
Filter output data rate select bits. The 10 bits of data programmed into these bits determine the filter
cutoff frequency, the position of the first notch of the filter, and the output data rate for the part. In
association with the gain selection, it also determines the output noise (and, therefore, the effective
resolution) of the device. (see Table 6 through Table 13)
When chop is disabled and continuous conversion mode is selected, the output data rate equals
Output Data Rate = (fmod/64)/FS
where FS is the decimal equivalent of the code in bits FS0 to FS9 and is in the range 1 to 1023, and
fmod is the modulator frequency, which is equal to MCLK/16. With a nominal MCLK of 4.92 MHz, this
results in a output data rate from 4.69 Hz to 4.8 kHz. With chop disabled, the filter first notch
frequency is equal to the output data rate when converting on a single channel.
When chop is enabled, the output data rate equals
Output Data Rate = (fmod/64)/(N × FS)
where:
FS is the decimal equivalent of the code in Bit FS0 to Bit FS9 and is in the range 1 to 1023.
fmod is the modulator frequency, which is equal to MCLK/16. With a nominal MCLK of 4.92 MHz, this
results in a conversion rate from 4.69/N Hz to 4.8/N kHz, where N is the order of the sinc filter. The sinc
filter’s first notch frequency is equal to N × Output Data Rate. The chopping introduces notches at odd
integer multiples of (Output Data Rate/2).
相關PDF資料 |
PDF描述 |
|---|---|
| AD7191BRUZ | IC ADC 2CH 24B SD 24TSSOP |
| AD7192BRUZ | IC ADC 24BIT 2CH W/PGA 24-TSSOP |
| AD7193BCPZ | IC ADC 24BIT SPI 4.8KHZ 32LFCSP |
| AD7194BCPZ | IC ADC 24BIT SPI 4.8K 32-LFCSP |
| AD7195BCPZ-RL7 | IC AFE 24BIT 4.8K 32LFSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7190WBRUZ | 功能描述:24 Bit Analog to Digital Converter 2, 4 Input 1 Sigma-Delta 24-TSSOP 制造商:analog devices inc. 系列:- 包裝:管件 零件狀態:有效 位數:24 采樣率（每秒）:4.8k 輸入數:2，4 輸入類型:差分，個偽差分 數據接口:SPI，DSP 配置:MUX-PGA-ADC 無線電 - S/H:ADC:- A/D 轉換器數:1 架構:三角積分 參考類型:外部， 內部 電壓 - 電源，模擬:5V 電壓 - 電源，數字:2.7 V ~ 5.25 V 特性:PGA，溫度傳感器 工作溫度:-40°C ~ 105°C 封裝/外殼:24-TSSOP（0.173"，4.40mm 寬） 供應商器件封裝:24-TSSOP 標準包裝:1 |
| AD7190WBRUZ-RL | 制造商:Analog Devices 功能描述: |
| AD7191 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Pin-Programmable, Ultralow Noise, 24-Bit, Sigma-Delta ADC for Bridge Sensors |
| AD7191A/0B | 制造商:Sony Nec Optiarc America 功能描述:DOUBLE DUAL INTERNAL DVDRW PATA BEZEL 20X/18X12XRAM - Bulk |
| AD7191BRUZ | 功能描述:IC ADC 2CH 24B SD 24TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
發布緊急采購，3分鐘左右您將得到回復。