參數資料
型號： ACS8946T
廠商： Semtech
文件頁數： 6/40頁
文件大?。?/td> 0K
描述： IC JITTER ATT MULT PLL 48-QFN
標準包裝： 1
類型： 時鐘/頻率發生器，多路復用器
PLL： 是
主要目的： 以太網，SONET/SDH
輸入： LVPECL
輸出： CML，LVPECL
電路數： 1
比率 - 輸入:輸出： 2:4
差分 - 輸入:輸出： 是/是
頻率 - 最大： 625MHz
電源電壓： 3.135 V ~ 3.465 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 48-VFQFN 裸露焊盤
供應商設備封裝： 48-QFN（7x7）
包裝： 托盤
ADVANCED COMMUNICATIONS
FINAL
DATASHEET
Revision 3/November 2006 Semtech Corp.
Page 14
www.semtech.com
ACS8946 JAM PLL
Define/change the frequencies of the dynamically
controllable outputs OUT1/OUT2 by driving the
RATE[2:1]A/B pins high or low in accordance with the
AB pattern for the required frequency as given in
Using CFG_IN[3:2], select the output interface type
(CML/LVPECL) for outputs OUT1 and OUT2. (See
Using CFG_IN[7:6], enable/disable LOCKB, select the
required output interface type for OUT3/OUT4 and set
any odd division. If odd division is not required, set to
1. (See Table 13).
Example Configuration
Decide which set of four output rates is most appropriate
for the application and look for the configuration that
provides these “Available Rates” in Table 11. E.g. If
77.76 MHz, 38.88 MHz, 19.44 MHz and 0ff are required,
then configuration No. 34 in Table 11 will suffice, i.e.
connect CFG_IN0 to ALARMC_CO3 and connect CFG_IN1
to CFG_OUT2.
To set OUT3 or OUT4 requires the additional configuration
of CFG_IN4 and CFG_IN5 as given by Table 12 (which also
configures RESYNC Edge). If OUT4 is required to be set to
“Off”, since “Off” has already been defined by previous
selection as AB=00 in Table 11, then look up the 00
pattern in Table 12, under “resulting RATE 4[AB]” (giving
rows 0 to3 and 16 to 19). Now refine the selection such
that OUT 3 provides 19.44 MHz output (AB=01) and a
rising RESYNC edge is required - this points to row 17 only,
i.e. connect CFG_IN4 to ALARM1_CO0 and connect
CFG_IN5 to ALARMC-CO3.
Set each of OUT[2:1] to one of these four Available Rates,
as required using the rate selection pins, e.g. to set
Output OUT2 to output 38.88 MHz, set RATE2A =1 and
RATE2B=0.
To configure an input to the required frequency of
77.76 MHz (and Output technology for OUT 1 and OUT2
only to CML), configure CFG_IN2 to GND and CFG_IN3 to
CFG_OUT2 as per row 2 in Table 10.
Table 13 provides the configuration information for using
pins CFG_IN[7:6] to configure whether LOCKB is enabled
or disabled, the value of the odd divider, and the port
interface type for OUT3 and OUT4. For example, assuming
LVPECL interface type is required, LOCKB is to be enabled
and the output rates (set previously according to Tables
11 and 12) are to be divided by 5 to give “Available
Rates” of Off, 3.888 MHz,7.776 MHz, 15.552 MHz, then
use the configuration in row 9 of Table 13, i.e. wire
CFG_IN6 to VDD and CFG_IN7 to ALARM2_CO1. The
corresponding frequency selections made for OUT[4:1]
will be divided by 5. The configuration of row 15 would be
used if the odd divider is not required (i.e. set to divide-
by-1).
Table 10 Input Divider, and OUT 1 and OUT2 Output Interface Type Configurations
Row
no.
Wiring of Configuration Pins
Output Application
Required Input
Frequency/
MHz
Resulting Highest
Available Output
Frequency/MHz
(when no further
division is selected)
Output Interface
Type for OUT1 and
OUT2
CFG_IN2
CFG_IN3
0
GND
ALARM1_CO0
SONET/SDH
155.52
622.08
CML
1
GND
ALARM2_CO1
SONET/SDH
155.52
622.08
LVPECL
2
GND
CFG_OUT2
SONET/SDH
77.76
622.08
CML
3
GND
ALARMC_CO3
SONET/SDH
77.76
622.08
LVPECL
4
VDD
GND
SONET/SDH
38.88
622.08
CML
5
VDD
SONET/SDH
38.88
622.08
LVPECL
6
VDD
ALARM1_CO0
SONET/SDH
19.44
622.08
CML
7
VDD
ALARM2_CO1
SONET/SDH
19.44
622.08
LVPECL
CFG_OUT2
ALARM1_CO0
Ethernet
125.00
625.00
CML
相關PDF資料
PDF描述
ACS8947T IC JITTER ATT MULT PLL 48-QFN
AD10200BZ IC ADC DUAL 12BIT 68-CLCC
AD10242BZ IC ADC DUAL 12BIT 68-CLCC
AD10465BZ IC ADC DUAL 14BIT 68-CLCC
AD13280AZ IC ADC 12BIT 68CLCC
相關代理商/技術參數
參數描述
ACS8947T 功能描述:IC JITTER ATT MULT PLL 48-QFN RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:- 標準包裝:1,500 系列:- 類型:時鐘緩沖器/驅動器 PLL:是 主要目的:- 輸入:- 輸出:- 電路數:- 比率 - 輸入:輸出:- 差分 - 輸入:輸出:- 頻率 - 最大:- 電源電壓:3.3V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:28-SSOP 包裝:帶卷 (TR) 其它名稱:93786AFT
ACS9010 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Optoelectronic
ACS9510/50EVB 制造商:Semtech Corporation 功能描述:
ACS9510EVB 功能描述:EVALUATION BOARD FOR ACS9510 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:ToPSync™ 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板
ACS9510T 制造商:Semtech Corporation 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*