- 您現在的位置：買賣IC網 > PDF目錄24832 > 935270056512 (NXP SEMICONDUCTORS) 4 CHANNEL(S), 5M bps, SERIAL COMM CONTROLLER, PQCC68 PDF資料下載
參數資料
| 型號： | 935270056512 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4 CHANNEL(S), 5M bps, SERIAL COMM CONTROLLER, PQCC68 |
| 封裝： | PLASTIC, MS-018, SOT-188-2, LCC-68 |
| 文件頁數： | 2/52頁 |
| 文件大?。?/td> | 680K |
| 代理商： | 935270056512 |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
Philips Semiconductors
SC16C754
Quad UART with 64-byte FIFO
Product data
Rev. 02 — 14 March 2003
10 of 49
9397 750 11192
Koninklijke Philips Electronics N.V. 2003. All rights reserved.
6.2.2
Auto-CTS
The transmitter circuitry checks CTS before sending the next data byte. When CTS is
active, the transmitter sends the next byte. To stop the transmitter from sending the
following byte, CTS must be deasserted before the middle of the last stop bit that is
currently being sent. The auto-CTS function reduces interrupts to the host system.
When ow control is enabled, CTS level changes do not trigger host interrupts
because the device automatically controls its own transmitter. Without auto-CTS, the
transmitter sends any data present in the transmit FIFO and a receiver overrun error
may result.
6.3 Software ow control
Software ow control is enabled through the enhanced feature register and the
modem control register. Different combinations of software ow control can be
enabled by setting different combinations of EFR[3:0]. Table 3 shows software ow
control options.
(1) N = receiver FIFO trigger level.
(2) The two blocks in dashed lines cover the case where an additional byte is sent, as described in Section 6.2.1.
Fig 5.
RTS functional timing.
START
BYTE N
START
BYTE N + 1
START
STOP
RX
RTS
IOR
N
N+1
12
002aaa226
(1) When CTS is LOW, the transmitter keeps sending serial data out.
(2) When CTS goes HIGH before the middle of the last stop bit of the current byte, the transmitter nishes sending the current
byte, but is does not send the next byte.
(3) When CTS goes from HIGH to LOW, the transmitter begins sending data again.
Fig 6.
CTS functional timing.
START
BYTE 0-7
STOP
TX
CTS
002aaa227
START
BYTE 0-7
STOP
Table 3:
Software ow control options (EFR[0:3])
EFR[3]
EFR[2]
EFR[1]
EFR[0]
TX, RX software ow controls
0
X
no transmit ow control
1
0
X
transmit Xon1, Xoff1
0
1
X
transmit Xon2, Xoff2
1
X
transmit Xon1, Xon2, Xoff1, Xoff2
相關PDF資料 |
PDF描述 |
|---|---|
| 935270071112 | 1 CHANNEL(S), 3M bps, SERIAL COMM CONTROLLER, PDIP40 |
| 935270058512 | 1 CHANNEL(S), 3M bps, SERIAL COMM CONTROLLER, PQCC44 |
| 935270058518 | 1 CHANNEL(S), 3M bps, SERIAL COMM CONTROLLER, PQCC44 |
| 935270070151 | 1 CHANNEL(S), 3M bps, SERIAL COMM CONTROLLER, PQFP48 |
| 935270070157 | 1 CHANNEL(S), 3M bps, SERIAL COMM CONTROLLER, PQFP48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 935270713557 | 制造商:NXP Semiconductors 功能描述:SUB ONLY IC CHP |
| 935270792551 | 制造商:NXP Semiconductors 功能描述:IC BUFF DVR TRI-ST 16BIT 56VFBGA |
| 935270792557 | 制造商:NXP Semiconductors 功能描述:IC BUFF DVR TRI-ST 16BIT 56VFBGA |
| 935270793551 | 制造商:NXP Semiconductors 功能描述:IC BUS TRCVR 3-ST 16BIT 56VFBGA |
| 935270793557 | 制造商:NXP Semiconductors 功能描述:IC BUS TRCVR 3-ST 16BIT 56VFBGA |
發布緊急采購，3分鐘左右您將得到回復。