- 您現在的位置：買賣IC網 > PDF目錄366259 > 8213AM Telecommunication IC PDF資料下載
參數資料
| 型號： | 8213AM |
| 英文描述： | Telecommunication IC |
| 中文描述： | 通信集成電路 |
| 文件頁數： | 10/33頁 |
| 文件大?。?/td> | 171K |
| 代理商： | 8213AM |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
SM8213AM
NIPPON PRECISION CIRCUITS—10
Battery Saving (BS1, BS2, BS3)
The SM8213AM controls the intermittent-duty oper-
ation of the RF stage, which reduces battery con-
sumption, and three output control signals (BS1,
BS2, BS3). The function each signal controls in each
mode is described below.
I
BS1 (RF-control main output signal)—The RF
stage is active when BS1 is HIGH. The rising-
edge setup time for receive timing is set by flags
RF0 to RF5 (61 steps). The maximum setup time
is 25.417 ms at 2400 bps, 50.833 ms at 1200 bps,
and 119.141 ms at 512 bps. Note that 3E
H
and
3F
H
are invalid settings for BS1.
I
BS2 (RF DC-level adjustment signal)—BS2 is
used to control the discharge of the receive signal
DC-cut capacitor. The function of BS2 is deter-
mined by flag BS2, as described below.
When flag BS2 is 0, pin BS2 goes HIGH
together with BS1 and then goes LOW again
after the BS1 setup time (idle mode). In pream-
ble and lock mode (during address/message
reception), it stays LOW.
When flag BS2 is 1, pin BS2 goes HIGH during
lock mode sync code receive timing and idle
mode signal receive timing. In preamble mode,
it stays LOW.
I
BS3 (PLL setup signal)—BS3 is used to control
PLL operation when the PLL is used. The rising-
edge setup time for receive timing is set by flags
PL0 to PL5 (61 steps). The maximum setup time
is 25.833 ms at 2400 bps, 51.667 ms at 1200 bps,
and 121.094 ms at 512 bps. Note that 3F
H
is an
invalid setting for BS3.
Note that the setup times should be set up such that
(BS3 rising-edge setup time) > (BS1 rising-edge
setup time).
Figure 3. BS1, BS2 and BS3 timing (Lock mode, frame 3)
S
I
M
A
I
M
I
A
M
M
M
M
I
I
I
A
M
S
M
M
M
M
I
I
A
Self address
M
M
M
M
I
A
M
S
A
M
0
1
2
3
4
5
6
7
0
1
3
4
5
6
7
2
0
1
2
3
4
5
6
7
0
1
3
4
5
6
7
2
S
M
A
S
M
M
I
I
I
I
M
M
M
M
M
M
M
M
S
M
M
M
I
A
M
M
M
I
A
M
I
I
I
M
M
Self address
1.953*Nms (0.833*Nms)
[0.417*Nms]
1.953*Mms
(0.833*Mms) [0.417*Mms]
1.953*Nms (0.833*Nms)
[0.417*Nms]
1.953*Mms
(0.833*Mms) [0.417*Mms]
BREAK detection to reception stop (32 bit max.)
Receive code
BS1
BREAK command
BS2
(flag BS2 option = 0)
BS2
(flag BS2 option = 1)
BS3
Receive code
BS1
BS2
(flag BS2 option = 0)
BS2
(flag BS2 option = 1)
BS3
Address does not match
相關PDF資料 |
PDF描述 |
|---|---|
| 8215-8009 | STECKER SUB D STAHLKRAGEN 15POL |
| 8225-8009 | STECKER SUB D STAHLKRAGEN 25POL |
| 8209-8009 | STECKER SUB D STAHLKRAGEN 9POL |
| 8237-8009 | STECKER SUB D STAHLKRAGEN 37POL |
| 821INSTSET | MPC821 PowerPC Instruction Set |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 8213B/13 | 制造商:WIELAND 功能描述:15 A, STRIP TERMINAL BLOCK, 1 ROW, 1 DECK |
| 8213B/15VR | 制造商:Wieland 功能描述:15 A, STRIP TERMINAL BLOCK, 1 ROW, 1 DECK |
| 8213B/20 | 制造商:WIELAND 功能描述:15 A, STRIP TERMINAL BLOCK, 1 ROW, 1 DECK |
| 8213B/3-OB | 制造商:Wieland Electric Inc 功能描述: |
| 8213B/4 | 制造商:Wieland 功能描述:15 A, STRIP TERMINAL BLOCK, 1 ROW, 1 DECK |
發布緊急采購，3分鐘左右您將得到回復。