- 您現在的位置：買賣IC網 > PDF目錄376463 > XRT83VSH38 (Exar Corporation) 8-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT PDF資料下載
參數資料
| 型號： | XRT83VSH38 |
| 廠商： | Exar Corporation |
| 英文描述： | 8-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT |
| 中文描述： | 8通道的T1/E1/J1短途線路接口單元 |
| 文件頁數： | 14/76頁 |
| 文件大?。?/td> | 722K |
| 代理商： | XRT83VSH38 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁
XRT83VSH38
11
8-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT
REV. 1.0.7
JITTER ATTENUATOR
CLOCK SYNTHESIZER
ATAOS
T13
I
Synchronous Microprocessor Clock/Automatic Transmit All Ones
Hardware Mode
This pin is used select an all ones signal to the line interface through TTIP/TRING any
time that a loss of signal occurs. This feature is avaiable in Host mode by program-
ming the appropriate global register.
N
OTE
:
Internally pulled “Low” with a 50k
resistor.
INT
L16
O
Interrupt Output
Host Mode
This signal is asserted "Low" when a change in alarm status occurs. Once the status
registers have been read, the interrupt pin will return "High". GIE (Global Interrupt
Enable) must be set "High" in the appropriate global register to enable interrupt gen-
eration.
N
OTES
:
1.
This pin is an open-drain output that requires an external 10K
pull-up
resistor.
2.
This pin has an internal PULL-DOWN 50k
resistor
S
IGNAL
N
AME
BGA
L
EAD
#
T
YPE
D
ESCRIPTION
JASEL0
JASEL1
A14
B13
I
Jitter Attenuator Select Pins Hardware Mode
JASEL[1:0] pins are used to place the jitter attenuator in the transmit path, the receive
path or to disable it.
N
OTE
:
These pins are internally pulled “Low” with 50k
resistors.
S
IGNAL
N
AME
BGA
L
EAD
#
T
YPE
D
ESCRIPTION
MCLKOUT
H1
O
Synthesized Master Clock Output
This signal is the output of the Master Clock Synthesizer PLL which is at T1 or E1
rate based upon the mode of operation.
MCLKT1
K1
I
T1 Master Clock Input
This signal is an independent 1.544MHz clock for T1 systems with accuracy better
than ±50ppm and duty cycle within 40% to 60%. MCLKT1 is used in the T1 mode.
N
OTE
:
All channels must operate at the same clock rate, either T1, E1 or J1. This
pin is internally pulled "Low" with a 50k
resistor.
S
IGNAL
N
AME
BGA
L
EAD
#
T
YPE
D
ESCRIPTION
Disabled
Transmit
Receive
Receive
JA Path
JA BW Hz
T1
--------
32/32
32/32
64/64
FIFO Size
-----
3
3
3
-----
10
10
1.5
0
0
1
1
JASEL1
0
1
0
1
JASEL0
E1
相關PDF資料 |
PDF描述 |
|---|---|
| XRT83VSH38IB | 8-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT |
| XRT84L14 | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
| XRT84L18 | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
| XRT84L38 | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
| XRT84L38_06 | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT83VSH38ES | 功能描述:外圍驅動器與原件 - PCI 8CH T1/E1LIUSH (low cost version) RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT83VSH38IB | 功能描述:接口 - 專用 8CH SH T1/E1 Line RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| XRT83VSH38IB-F | 功能描述:外圍驅動器與原件 - PCI 8 Channel Short-Haul RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT83VSH38IB-F | 制造商:Exar Corporation 功能描述:T1/E1 LIU IC |
| XRT84L38 | 制造商:EXAR 制造商全稱:EXAR 功能描述:OCTAL T1/E1/J1 FRAMER |
發布緊急采購，3分鐘左右您將得到回復。