參數資料
型號: W25X16-VSFI
廠商: WINBOND ELECTRONICS CORP
元件分類: PROM
英文描述: 16M X 1 FLASH 2.7V PROM, PDSO16
封裝: 0.300 INCH, SOIC-16
文件頁數: 17/47頁
文件大小: 1317K
代理商: W25X16-VSFI
W25X16, W25X32, W25X64
- 24 -
11.2.10 Page Program (02h)
The Page Program instruction allows up to 256 bytes of data to be programmed at previously erased
to all 1s (FFh) memory locations. A Write Enable instruction must be executed before the device will
accept the Page Program Instruction (Status Register bit WEL must equal 1). The instruction is
initiated by driving the /CS pin low then shifting the instruction code “02h” followed by a 24-bit address
(A23-A0) and at least one data byte, into the DIO pin. The /CS pin must be held low for the entire
length of the instruction while data is being sent to the device. The Page Program instruction
sequence is shown in figure 11.
If an entire 256 byte page is to be programmed, the last address byte (the 8 least significant address
bits) should be set to 0. If the last address byte is not zero, and the number of clocks exceed the
remaining page length, the addressing will wrap to the beginning of the page. In some cases, less
than 256 bytes (a partial page) can be programmed without having any effect on other bytes within the
same page. One condition to perform a partial page program is that the number of clocks can not
exceed the remaining page length. If more than 256 bytes are sent to the device the addressing will
wrap to the beginning of the page and overwrite previously sent data.
As with the write and erase instructions, the /CS pin must be driven high after the eighth bit of the last
byte has been latched. If this is not done the Page Program instruction will not be executed. After /CS
is driven high, the self-timed Page Program instruction will commence for a time duration of tpp (See
AC Characteristics). While the Page Program cycle is in progress, the Read Status Register
instruction may still be accessed for checking the status of the BUSY bit. The BUSY bit is a 1 during
the Page Program cycle and becomes a 0 when the cycle is finished and the device is ready to accept
other instructions again. After the Page Program cycle has finished the Write Enable Latch (WEL) bit
in the Status Register is cleared to 0. The Page Program instruction will not be executed if the
addressed page is protected by the Block Protect (BP2, BP1, and BP0) bits (see Status Register
Memory Protection table).
Figure 11. Page Program Instruction Sequence Diagram
相關PDF資料
PDF描述
W25Q64CVSSAG 64M X 1 SPI BUS SERIAL EEPROM, PDSO8
WS32K32-100HC 128K X 8 MULTI DEVICE SRAM MODULE, 100 ns, CHIP66
WS128K32-25G4CE 512K X 8 MULTI DEVICE SRAM MODULE, 25 ns, CQFP68
WMS128K8L-35DEQE 128K X 8 STANDARD SRAM, 35 ns, CDSO32
WMF512K8X-120CLQ5 512K X 8 FLASH 5V PROM, 120 ns, CQCC32
相關代理商/技術參數
參數描述
W25X16VSFIG 功能描述:IC FLASH 16MBIT 75MHZ 16SOIC RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:SpiFlash® 標準包裝:1,000 系列:- 格式 - 存儲器:RAM 存儲器類型:移動 SDRAM 存儲容量:256M(8Mx32) 速度:133MHz 接口:并聯 電源電壓:1.7 V ~ 1.95 V 工作溫度:-40°C ~ 85°C 封裝/外殼:90-VFBGA 供應商設備封裝:90-VFBGA(8x13) 包裝:帶卷 (TR) 其它名稱:557-1327-2
W25X16VSFIG T&R 功能描述:IC FLASH 16MBIT 75MHZ 16SOIC RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:SpiFlash® 標準包裝:1,000 系列:- 格式 - 存儲器:RAM 存儲器類型:移動 SDRAM 存儲容量:256M(8Mx32) 速度:133MHz 接口:并聯 電源電壓:1.7 V ~ 1.95 V 工作溫度:-40°C ~ 85°C 封裝/外殼:90-VFBGA 供應商設備封裝:90-VFBGA(8x13) 包裝:帶卷 (TR) 其它名稱:557-1327-2
W25X16VSFIZ 制造商:WINBOND 制造商全稱:Winbond 功能描述:16M-BIT, 32M-BIT, AND 64M-BIT SERIAL FLASH MEMORY WITH 4KB SECTORS AND DUAL OUTPUT SPI
W25X16VSSI 制造商:WINBOND 制造商全稱:Winbond 功能描述:16M-BIT, 32M-BIT, AND 64M-BIT SERIAL FLASH MEMORY WITH 4KB SECTORS AND DUAL OUTPUT SPI
W25X16VSSIG 功能描述:IC FLASH 16MBIT 75MHZ 8SOIC RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:SpiFlash® 標準包裝:1,000 系列:- 格式 - 存儲器:RAM 存儲器類型:移動 SDRAM 存儲容量:256M(8Mx32) 速度:133MHz 接口:并聯 電源電壓:1.7 V ~ 1.95 V 工作溫度:-40°C ~ 85°C 封裝/外殼:90-VFBGA 供應商設備封裝:90-VFBGA(8x13) 包裝:帶卷 (TR) 其它名稱:557-1327-2