參數資料
型號： T89C5115-TISUM
廠商： Atmel
文件頁數： 17/113頁
文件大?。?/td> 0K
描述： IC 8051 MCU FLASH 16K 28SOIC
標準包裝： 27
系列： 89C
核心處理器： 8051
芯體尺寸： 8-位
速度： 40MHz
連通性： UART/USART
外圍設備： POR，PWM，WDT
輸入/輸出數： 20
程序存儲器容量： 16KB（16K x 8）
程序存儲器類型： 閃存
EEPROM 大小： 2K x 8
RAM 容量： 512 x 8
電壓 - 電源 (Vcc/Vdd)： 3 V ~ 5.5 V
數據轉換器： A/D 8x10b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 28-SOIC（0.295"，7.50mm 寬）
包裝： 管件
其它名稱： 89C5115-TISUM
2007-2011 Microchip Technology Inc.
DS70265E-page 113
dsPIC33FJ12MC201/202
9.0
POWER-SAVING FEATURES
The dsPIC33FJ12MC201/202 devices provide the
ability to manage power consumption by selectively
managing clocking to the CPU and the peripherals. In
general, a lower clock frequency and a reduction in the
number of circuits being clocked constitutes lower
consumed power. dsPIC33FJ12MC201/202 devices
can manage power consumption in four different ways:
Clock frequency
Instruction-based Sleep and Idle modes
Software-controlled Doze mode
Selective peripheral control in software
Combinations of these methods can be used to selec-
tively tailor an application’s power consumption while
still maintaining critical application features, such as
timing-sensitive communications.
9.1
Clock Frequency and Clock
Switching
dsPIC33FJ12MC201/202 devices allow a wide range
of clock frequencies to be selected under application
control. If the system clock configuration is not locked,
users can choose low-power or high-precision
oscillators by simply changing the NOSC bits
(OSCCON<10:8>). The process of changing a system
clock during operation, as well as limitations to the
process, are discussed in more detail in Section 8.0
.
9.2
Instruction-Based Power-Saving
Modes
dsPIC33FJ12MC201/202 devices have two special
power-saving modes that are entered through the
execution of a special PWRSAV instruction. Sleep mode
stops clock operation and halts all code execution. Idle
mode halts the CPU and code execution, but allows
peripheral modules to continue operation. The
assembler syntax of the PWRSAV instruction is shown in
Sleep and Idle modes can be exited as a result of an
enabled interrupt, WDT time-out or a device Reset. When
the device exits these modes, it is said to wake-up.
9.2.1
SLEEP MODE
The following occur in Sleep mode:
The system clock source is shut down. If an
on-chip oscillator is used, it is turned off.
The device current consumption is reduced to a
minimum, provided that no I/O pin is sourcing
current
The Fail-Safe Clock Monitor does not operate,
since the system clock source is disabled
The LPRC clock continues to run in Sleep mode if
the WDT is enabled
The WDT, if enabled, is automatically cleared
prior to entering Sleep mode
Some device features or peripherals may continue
to operate. This includes items such as the input
change notification on the I/O ports, or peripherals
that use an external clock input.
Any peripheral that requires the system clock
source for its operation is disabled
The device will wake-up from Sleep mode on any of the
these events:
Any interrupt source that is individually enabled
Any form of device Reset
A WDT time-out
On wake-up from Sleep mode, the processor restarts
with the same clock source that was active when Sleep
mode was entered.
EXAMPLE 9-1:
PWRSAV
INSTRUCTION SYNTAX
Note 1:
This data sheet summarizes the features
of the dsPIC33FJ12MC201/202 family of
devices. It is not intended to be a
comprehensive reference source. To
complement the information in this data
sheet, refer to Section 9. “Watchdog
Timer
and
Power-Saving
Modes”
(DS70196) of the “dsPIC33F/PIC24H
Family Reference Manual”
, which is
(www.microchip.com).
2:
Some registers and associated bits
described in this section may not be
available on all devices. Refer to
in
this data sheet for device-specific register
and bit information.
Note:
SLEEP_MODE
and
IDLE_MODE
are
constants defined in the assembler
include file for the selected device.
PWRSAV
#SLEEP_MODE
; Put the device into Sleep mode
PWRSAV
#IDLE_MODE
; Put the device into Idle mode
相關PDF資料
PDF描述
T89C51AC2-SLSIM IC 8051 MCU FLASH 32K 44PLCC
T89C51CC01UA-7CTIM IC 8051 MCU FLASH 32K 64BGA
T89C51CC02UA-TDSIM IC 8051 MCU FLASH 16K 24-SOIC
TC520ACOE713 IC SERIAL INTERFACE ADT 16SOIC
TC530COI713 IC DATA ACQ SUBSYSTEM 28SOIC
相關代理商/技術參數
參數描述
T89C5121 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Microcontroller with MULTI-PROTOCOL SMART CARD INTERFACE
T89C5121-ICRIL 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Microcontroller with MULTI-PROTOCOL SMART CARD INTERFACE
T89C5121-ICSIL 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Microcontroller with Multi protocol SMART Card Interface
T89C5121-ICSUL 制造商:Atmel Corporation 功能描述:
T89C5121-ICUIL 功能描述:IC 8051 MCU W/SMART CARD 24SSOP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:89C 產品培訓模塊:MCU Product Line Introduction XMEGA Introduction AVR XMEGA USB Connectivity 標準包裝:90 系列:AVR® XMEGA 核心處理器:AVR 芯體尺寸:8/16-位 速度:32MHz 連通性:I²C，IrDA，SPI，UART/USART 外圍設備:欠壓檢測/復位，DMA，POR，PWM，WDT 輸入/輸出數:50 程序存儲器容量:192KB（96K x 16） 程序存儲器類型:閃存 EEPROM 大小:4K x 8 RAM 容量:16K x 8 電壓 - 電源 (Vcc/Vdd):1.6 V ~ 3.6 V 數據轉換器:A/D 16x12b; D/A 2x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:64-TQFP 包裝:托盤 配用:ATSTK600-RC14-ND - STK600 SOCKET/ADAPTER 64TQFPATSTK600-TQFP64-ND - STK600 SOCKET/ADAPTER 64-TQFPATAVRONEKIT-ND - KIT AVR/AVR32 DEBUGGER/PROGRMMRATAVRISP2-ND - PROGRAMMER AVR IN SYSTEM
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*