- 您現在的位置：買賣IC網 > PDF目錄383876 > T8535 (Lineage Power) Quad Programmable Codec(四通道可編程編解碼器) PDF資料下載
參數資料
| 型號： | T8535 |
| 廠商： | Lineage Power |
| 元件分類： | Codec |
| 英文描述： | Quad Programmable Codec(四通道可編程編解碼器) |
| 中文描述： | 四可編程編解碼器（四通道可編程編解碼器） |
| 文件頁數： | 16/54頁 |
| 文件大?。?/td> | 1872K |
| 代理商： | T8535 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁
16
Lucent Technologies Inc.
Preliminary Data Sheet
July 2000
T8535/T8536 Quad Programmable Codec
Functional Description
(continued)
The Control Interface
(continued)
Protocol
The format of the command protocol is shown in Fig-
ures 6 and 7.
The control interface operates with one external master
controller and multiple slave codec devices. Each
transfer is initiated by the master, and the slave
responds for either read operations or the fast scan
mode. The slave does not check the bus for activity
prior to transmitting; it only checks for an active CS.
The master should allow for a wait between the end of
a read command until CS becomes active for the read
data. The master must refrain from sending additional
commands to the slave chip until the response is
received. On a 4-wire bus, commands to other devices
may be initiated before the response is received, but
care in generating the CS function is needed to ensure
that the multiple responses do not interfere. It should
be noted that multiple memory locations can be
accessed in the same command by setting the data
field length field to the desired number of bytes to be
transferred. If flow control is desired, it must be per-
formed by using separate commands, each transfer-
ring smaller blocks of information, or by controlling the
serial clock (gapping the serial clock), or with CS in the
case of byte-by-byte mode.
There is no response from the slave to the master for a
write operation. The response to a read operation sim-
ply includes the data to be read in the data field. This
data is sent least significant bit first, with the bytes sent
in ascending sequence. Commands from the master
controller include data for write operations, but not for
read operations. Since the coefficients and gains are
stored in volatile memory, all the coefficients and gains
must be loaded after powerup. There is, however, no
need to reload them when switching from active to
standby modes, or vice versa. Great care should be
exercised in loading memory when the codec channel
is not in standby mode. Sudden changes in the termi-
nation or balance impedances can result in undesirable
system operation.
All data is transmitted in a byte-oriented fashion with
the least significant bit of each byte transferred first.
Multibyte fields are transferred least significant byte
first in both directions. The data field will contain the
first addressed data location first, with subsequent data
locations transmitted in ascending order.
相關PDF資料 |
PDF描述 |
|---|---|
| T8538A | Quad Programmable Codec(四通道可編程編解碼器) |
| T85HF10 | POWER RECTIFIER DIODES |
| T85HF100 | POWER RECTIFIER DIODES |
| T85HF120 | POWER RECTIFIER DIODES |
| T85HF20 | POWER RECTIFIER DIODES |
相關代理商/技術參數 |
參數描述 |
|---|---|
| T8535B | 制造商:AGERE 制造商全稱:AGERE 功能描述:T8535B/T8536B Quad Programmable Codec |
| T8536B | 制造商:AGERE 制造商全稱:AGERE 功能描述:T8535B/T8536B Quad Programmable Codec |
| T8538B | 制造商:AGERE 制造商全稱:AGERE 功能描述:T8538B Quad Programmable Codec |
| T85471G | 制造商:BITECH 制造商全稱:Bi technologies 功能描述:Thick Film Super Low Profile SIP Resistor Networks |
| T85471J | 制造商:BITECH 制造商全稱:Bi technologies 功能描述:Thick Film Super Low Profile SIP Resistor Networks |
發布緊急采購，3分鐘左右您將得到回復。