參數資料
型號： STA304A
廠商： 意法半導體
英文描述： 20 POS IMAGE SENSOR SOCKT
中文描述： 數字音頻處理器多通道的DDX⑩
文件頁數： 18/30頁
文件大?。?/td> 338K
代理商： STA304A
STA304A
18/30
where CH stands for LR,SUR or SBW and x stands for the filter number (0..3).
The filter equation is Yn = Xn+((b0)-1)*Xn + 2*((b1)/2)*Xn-1 + b2*Xn-2 - 2*((a1)/2)*Yn-1 - a2*Yn-2 =
= b0*Xn + b1*Xn-1 + b2*Xn-2 - a1*Yn-1 - a2*Yn-2
The coefficient registers are 20 bits wide and should be in the range [-1..1) (80000h to 7ffffh).
Scaling factor registers:
For the filters Xn = - (-scale_in) * CHn , where CHn is the value before scaling and Xn is the input to the filter.
For the SBW redirection SBWn = -S (-scale_CH)*CHn
The scaling factor registers are 20 bits wide and should be in the range [-1..0] (80000h to 00000h).
SBW redirection: -1 for maximum redirection and 0 for no redirection.
Filter scaling: -1 for maximum input and 0 for no input to filter.
11.0I
2
C BUS SPECIFICATION
The STA304A supports the I
2
C protocol. This protocol defines any device that sends data on to the bus as a
transmitter and any device that reads the data as a receiver. The device that controls the data transfer is known
as the master and the others as the slave. The master always starts the transfer and provides the serial clock
for synchronisation. The STA304A is always a slave device in all its communications.
16bit registers are addressed as two 8 bit registers. The high byte has even address, while the low byte has odd
address. For example, reading from register 02 (16bit) means read registers 02 (HIGH BYTE) and 03 (LOW
BYTE) from I
2
C.
11.1COMMUNICATION PROTOCOL
11.1.1Data transition or change
Data changes on the SDA line must only occur when the SCL clock is low. SDA transition while the clock is high
are used to identify START or STOP condition.
11.1.2Start condition
START is identified by a high to low transition of the data bus SDA signal while the clock signal SCL is stable
in the high state.A START condition must precede any command for data transfer.
11.1.3Stop condition
STOP is identified by low to high transition of the data bus SDA signal while the clock signal SCL is stable in the
high state. A STOP condition terminates communications between STA304A and the bus master.
11.1.4Acknowledge bit
An acknowledge bit is used to indicate a successful data transfer. The bus transmitter, either master or slave,
releases the SDA bus after sending 8 bit of data.
During the 9th clock pulse the receiver pulls the SDA bus low to acknowledge the receipt of 8 bits of data.
11.1.5Data input
During the data input the STA304A samples the SDA signal on the rising edge of the clock SCL.
For correct device operation the SDA signal has to be stable during the rising edge of the clock and the data
can change only when the SCL line is low.
11.2DEVICE ADDRESSING
To start communication between the master and the STA304A, the master must initiate with a start condition.
Following this, the master sends onto the SDA line 8 bits (MSB first) corresponding to the device select address
相關PDF資料
PDF描述
STA400A XMRADIO SDARS CHANNEL DECODER
STA450A XMRADIO SDARS SERVICE LAYER & SOURCE DECODER
STA508 40V 4.5A QUAD POWER HALF BRIDGE
STABP01 GT 7C 7#16S SKT PLUG RTANG
STABP01D GT 5C 5#16S SKT PLUG
相關代理商/技術參數
參數描述
STA305 制造商:SANKEN 制造商全稱:Sanken electric 功能描述:PNP Darlington 3-phase motor drive
STA305A 制造商:SANKEN 制造商全稱:Sanken electric 功能描述:PNP Darlington 3-phase motor drive
STA306 功能描述:多媒體雜項 AUDIO SYSTEMS RoHS:否 制造商:Texas Instruments 類型: 通道數量: 轉換速率:540 Mbps 分辨率: 封裝 / 箱體:SOIC-16 封裝:Tube
STA30613TR 功能描述:多媒體雜項 AUDIO SYSTEMS RoHS:否 制造商:Texas Instruments 類型: 通道數量: 轉換速率:540 Mbps 分辨率: 封裝 / 箱體:SOIC-16 封裝:Tube
STA308 功能描述:音頻 DSP Digital Audio Procsr RoHS:否 制造商:Texas Instruments 工作電源電壓: 電源電流: 工作溫度范圍: 安裝風格: 封裝 / 箱體: 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*