參數資料
型號: ST7PL05Y0MB
廠商: STMICROELECTRONICS
元件分類: 微控制器/微處理器
英文描述: 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO16
封裝: 0.150 INCH, PLASTIC, SOP-16
文件頁數: 42/108頁
文件大?。?/td> 2098K
代理商: ST7PL05Y0MB
ST7L0
39/108
I/O PORTS (Cont’d)
CAUTION: The alternate function must not be ac-
tivated as long as the pin is configured as input
with interrupt, in order to avoid generating spurious
interrupts.
Analog alternate function
When the pin is used as an ADC input, the I/O
must be configured as floating input. The analog
multiplexer (controlled by the ADC registers)
switches the analog voltage present on the select-
ed pin to the common analog rail which is connect-
ed to the ADC input.
It is recommended not to change the voltage level
or loading on any port pin while conversion is in
progress. Furthermore it is recommended not to
have clocking pins located close to a selected an-
alog pin.
WARNING: The analog input voltage level must
be within the limits stated in the absolute maxi-
mum ratings.
10.3 UNUSED I/O PINS
Unused I/O pins must be connected to fixed volt-
age levels. Refer to Section 13.8.
10.4 LOW POWER MODES
10.5 INTERRUPTS
The external interrupt event generates an interrupt
if the corresponding configuration is selected with
DDR and OR registers and the interrupt mask in
the CC register is not active (RIM instruction).
10.6 I/O PORT IMPLEMENTATION
The hardware implementation on each I/O port de-
pends on the settings in the DDR and OR registers
and specific feature of the I/O port such as ADC In-
put.
Switching these I/O ports from one state to anoth-
er must be done in a sequence that prevents un-
wanted side effects. Recommended safe transi-
tions are illustrated in Figure 24 Other transitions
are potentially risky and should be avoided, since
they are likely to present unwanted side-effects
such as spurious interrupt generation.
Figure 24. Interrupt I/O Port State Transitions
The I/O port register configurations are summa-
rized as follows:
Table 11. Port Configuration
Mode
Description
WAIT
No effect on I/O ports. External interrupts
cause the device to exit from WAIT mode.
HALT
No effect on I/O ports. External interrupts
cause the device to exit from HALT mode.
Interrupt Event
Event
Flag
Enable
Control
Bit
Exit
from
Wait
Exit
from
Halt
External interrupt on
selected external
event
-
DDRx
ORx
Yes
01
floating/pull-up
interrupt
INPUT
00
floating
(reset state)
INPUT
10
open-drain
OUTPUT
11
push-pull
OUTPUT
XX
= DDR, OR
Port
Pin name
Input (DDR = 0)
Output (DDR = 1)
OR = 0
OR = 1
OR = 0
OR = 1
Port A
PA7
floating
pull-up interrupt
open drain
push-pull
PA6:1
floating
pull-up
open drain
push-pull
PA0
floating
pull-up interrupt
open drain
push-pull
Port B
PB4
floating
pull-up
open drain
push-pull
PB3
floating
pull-up interrupt
open drain
push-pull
PB2:1
floating
pull-up
open drain
push-pull
PB0
floating
pull-up interrupt
open drain
push-pull
1
相關PDF資料
PDF描述
ST7PLITE05F0U6TR 8-BIT, MROM, 16 MHz, MICROCONTROLLER, QCC20
ST7PLITE05Y0B6 8-BIT, MROM, 16 MHz, MICROCONTROLLER, PDIP16
ST7PLITE02F0U6TR 8-BIT, MROM, 16 MHz, MICROCONTROLLER, QCC20
ST7PLITE02Y0B6 8-BIT, MROM, 16 MHz, MICROCONTROLLER, PDIP16
ST7PLITE05Y0M3 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO16
相關代理商/技術參數
參數描述
ST7PLITE02F0U6TR 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT MICROCONTROLLER WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, TIMERS, SPI
ST7PLITE02Y0B6 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT MICROCONTROLLER WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, TIMERS, SPI
ST7PLITE02Y0B6TR 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-bit microcontroller with single voltage Flash memory, data EEPROM, ADC, timers, SPI
ST7PLITE02Y0M6 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-bit microcontroller with single voltage Flash memory, data EEPROM, ADC, timers, SPI
ST7PLITE02Y0M6TR 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-bit microcontroller with single voltage Flash memory, data EEPROM, ADC, timers, SPI