參數資料
型號： ST7FDALIF2M6
廠商： 意法半導體
元件分類： ADC
英文描述： 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, TIMERS, SPI, DALI
中文描述： 8位單電壓閃存存儲器，數據EEPROM，模數轉換器，定時器，SPI和大理微控制器
文件頁數： 73/141頁
文件大小： 2175K
代理商： ST7FDALIF2M6
ST7DALI
73/141
DALI COMMUNICATION MODULE
(Cont’d)
11.4.6 Special Functions
11.4.6.1 Forced Transmission (Test mode)
The DCM must receive a "forward frame" before
sending back a "backward frame". But it is possi-
ble to force the DCM into Transmit state by setting
the FTS bit in the DCMCR register. The DCMBD
register will be shifted out in DALI format, the Most
Significant Bit-first. Preferably before forcing the
DCM into Transmit state, the user should reset/set
the DCME bit in the DCMCR register. An interrupt
flag will be generated after a forced transmission
(the ITF bit in the DCMCSR register).
Procedure:
– Reset the DCME bit in the DCMCR register.
– Write the backward value in the DCMBD reg-
ister.
– Set both the DCME and the FTS bits in the
DCMCR register.
– When an interrupt is generated (end of trans-
mission, the ITF bit is set in the DCMCSR reg-
ister), set the RTA bit in the DCMCR register
to re-start a transmission.
– To return to normal DALI communications, re-
set/set the DCME bit and reset the FTS bit in
the DCMCR register.
11.4.6.2 Normal Transmission
After the "forward frame" reception, the software
must write the backward data byte to the DCMBD
register and set both the RTS and RTA bits in the
DCMCR register to start the transmission.
It is not possible to send a backward frame just af-
ter having sent a backward frame (see DALI
standard protocol).
11.4.6.3 DCM Enable
The user can enable or disable the DCM by writing
the DCME bit in the DCMCR register. This bit is
also used to reset the entire internal finite state
machine.
11.4.7 DALI Interface Failure
If the DALI input signal is set to low level for a 2-bit
period (1.66 ms), then the DCM generates an er-
ror flag by setting the EF bit in the DCMCSR regis-
ter. This bit can be cleared by reading the DCMC-
SR register. The interface failure is detected if the
DCM is in Receive state only.
11.4.8 Low Power Modes
11.4.9 Interrupts
Mode
WAIT
HALT
ACTIVE
HALT
Description
No effect on DCM
DCM registers are frozen
No effect on DCM
Interrupt
Event
Event
Flag
Enable
Control
Bit
ITE
Exit
from
Wait
Yes
Exit
from
Halt
No
EOT
ITF
1
相關PDF資料
PDF描述
ST7PDALIF2M6 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, TIMERS, SPI, DALI
ST7FLCD1 8-bit MCU for LCD Monitors with 60 KBytes Flash, 2 KBytes RAM, 2 DDC Ports and Infrared Controller
ST7FLIT19B 8-Bit MCU With Single Voltage Flash Memory, Data EEPROM, ADC, 5 Timers, SPI(內部RC,PLL,ADC,ROP,ICP, IAP,SPI的8位MCU)
ST7FLITE10F1B6 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, 4 TIMERS, SPI
ST7FLITE19F1M6 CLUSTER PANEL,RJ-11 W/ (12) 4-
相關代理商/技術參數
參數描述
ST7FDALIF2M6TR 功能描述:8位微控制器 -MCU 8 BITS MICROCONTR RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ST7FL05Y0MA 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-bit MCU for automotive with single voltage Flash memory, data EEPROM, ADC, timers, SPI
ST7FL05Y0MAE 功能描述:8位微控制器 -MCU 8-bit MCU Automotive RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ST7FL05Y0MATRE 制造商:STMicroelectronics 功能描述:SOCKET BOARD LITE - Tape and Reel
ST7FL05Y0MB 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-bit MCU for automotive with single voltage Flash memory, data EEPROM, ADC, timers, SPI
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*