- 您現在的位置：買賣IC網 > PDF目錄192300 > S29GL128N11FFIVH2 (SPANSION LLC) 16M X 16 FLASH 3V PROM, 110 ns, PBGA64 PDF資料下載
參數資料
| 型號： | S29GL128N11FFIVH2 |
| 廠商： | SPANSION LLC |
| 元件分類： | PROM |
| 英文描述： | 16M X 16 FLASH 3V PROM, 110 ns, PBGA64 |
| 封裝： | 10 X 13 MM, 1 MM PITCH, LEAD FREE, FBGA-64 |
| 文件頁數： | 36/74頁 |
| 文件大?。?/td> | 1593K |
| 代理商： | S29GL128N11FFIVH2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁當前第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁
May 1, 2006 S29GL-N_01_A0
S29GL-N
39
Data
She e t
Figure 10.2 Program Operation
Note
See Table 11.1 on page 46 and Table 11.3 on page 48 for program command sequence.
10.6
Program Suspend/Program Resume Command Sequence
The Program Suspend command allows the system to interrupt a programming operation or a Write to Buffer
programming operation so that data can be read from any non-suspended sector. When the Program
Suspend command is written during a programming process, the device halts the program operation within
15 s maximum (5 s typical) and updates the status bits. Addresses are not required when writing the
Program Suspend command.
After the programming operation is suspended, the system can read array data from any non-suspended
sector. The Program Suspend command may also be issued during a programming operation while an erase
is suspended. In this case, data may be read from any addresses not in Erase Suspend or Program Suspend.
If a read is needed from the Secured Silicon Sector area (One-time Program area), then user must use the
proper command sequences to enter and exit this region. Note that the Secured Silicon Sector autoselect,
and CFI functions are unavailable when program operation is in progress.
The system may also write the autoselect command sequence when the device is in the Program Suspend
mode. The system can read as many autoselect codes as required. When the device exits the autoselect
mode, the device reverts to the Program Suspend mode, and is ready for another valid operation. See
Autoselect Command Sequence on page 35 for more information.
After the Program Resume command is written, the device reverts to programming. The system can
determine the status of the program operation using the DQ7 or DQ6 status bits, just as in the standard
program operation. See Write Operation Status on page 50 for more information.
The system must write the Program Resume command (address bits are don’t care) to exit the Program
Suspend mode and continue the programming operation. Further writes of the Resume command are
ignored. Another Program Suspend command can be written after the device has resume programming.
START
Write Program
Command Sequence
Data Poll
from System
Verify Data?
No
Yes
Last Address?
No
Yes
Programming
Completed
Increment Address
Embedded
Program
algorithm
in progress
相關PDF資料 |
PDF描述 |
|---|---|
| S29JL032J70TFI213 | 2M X 16 FLASH 3V PROM, 70 ns, PDSO48 |
| S29PL032J65BFI150 | 2M X 16 FLASH 3V PROM, 65 ns, PBGA56 |
| S29PL127J70BFI000 | 8M X 16 FLASH 3V PROM, 70 ns, PBGA80 |
| S29XS064R0PBHW010 | 4M X 16 FLASH 1.8V PROM, 80 ns, PBGA44 |
| S2C3R-1-12-H | 4000 MHz - 12000 MHz RF/MICROWAVE SGL POLE DOUBLE THROW SWITCH, 2 dB INSERTION LOSS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S29GL128N11FFVR10 | 制造商:Spansion 功能描述:FLASH PARALLEL 3.3V 128MBIT 16MX8/8MX16 110NS 56TSOP - Trays |
| S29GL128N11TAI010 | 制造商:Spansion 功能描述:SPZS29GL128N11TAI010 FLSH MEM EOL161008 |
| S29GL128N11TFA020 | 制造商:Spansion 功能描述: |
| S29GL128N11TFI010H | 制造商:Spansion 功能描述: |
| S29GL128N11TFI020 | 制造商:Spansion 功能描述: 制造商:Spansion 功能描述:Flash - NOR IC 制造商:Spansion 功能描述:NOR Flash, 8M x 16, 56 Pin, Plastic, TSSOP |
發布緊急采購，3分鐘左右您將得到回復。