- 您現在的位置：買賣IC網 > PDF目錄192300 > S29GL128N11FAIVH0 (SPANSION LLC) 16M X 16 FLASH 3V PROM, 110 ns, PBGA64 PDF資料下載
參數資料
| 型號： | S29GL128N11FAIVH0 |
| 廠商： | SPANSION LLC |
| 元件分類： | PROM |
| 英文描述： | 16M X 16 FLASH 3V PROM, 110 ns, PBGA64 |
| 封裝： | 10 X 13 MM, 1 MM PITCH, FBGA-64 |
| 文件頁數： | 30/74頁 |
| 文件大?。?/td> | 1593K |
| 代理商： | S29GL128N11FAIVH0 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁
34
S29GL-N
S29GL-N_01_A0 May 1, 2006
Da ta
Sh e e t
10. Command Definitions
Writing specific address and data commands or sequences into the command register initiates device
operations. Table 11.1 on page 46 and Table 11.3 on page 48 define the valid register command sequences.
Writing incorrect address and data values or writing them in the improper sequence may place the device in
an unknown state. A reset command is then required to return the device to reading array data.
All addresses are latched on the falling edge of WE# or CE#, whichever happens later. All data is latched on
the rising edge of WE# or CE#, whichever happens first. Refer to AC Characteristics on page 59 for timing
diagrams.
10.1
Reading Array Data
The device is automatically set to reading array data after device power-up. No commands are required to
retrieve data. The device is ready to read array data after completing an Embedded Program or Embedded
Erase algorithm.
After the device accepts an Erase Suspend command, the device enters the erase-suspend-read mode, after
which the system can read data from any non-erase-suspended sector. After completing a programming
operation in the Erase Suspend mode, the system may once again read array data with the same exception.
See Erase Suspend/Erase Resume Commands on page 42 for more information.
The system must issue the reset command to return the device to the read (or erase-suspend-read) mode if
DQ5 goes high during an active program or erase operation, or if the device is in the autoselect mode. See
Reset Command on page 34 for more information.
See also Requirements for Reading Array Data on page 12 for more information. Read-Only Operations
on page 59 provides the read parameters, and Figure 18.1 on page 59 shows the timing diagram.
10.2
Reset Command
Writing the reset command resets the device to the read or erase-suspend-read mode. Address bits are don’t
cares for this command.
The reset command may be written between the sequence cycles in an erase command sequence before
erasing begins. This resets the device to the read mode. Once erasure begins, however, the device ignores
reset commands until the operation is complete.
The reset command may be written between the sequence cycles in a program command sequence before
programming begins. This resets the device to the read mode. If the program command sequence is written
while the device is in the Erase Suspend mode, writing the reset command returns the device to the erase-
suspend-read mode. Once programming begins, however, the device ignores reset commands until the
operation is complete.
The reset command may be written between the sequence cycles in an autoselect command sequence.
Once in the autoselect mode, the reset command must be written to return to the read mode. If the device
entered the autoselect mode while in the Erase Suspend mode, writing the reset command returns the device
to the erase-suspend-read mode.
If DQ5 goes high during a program or erase operation, writing the reset command returns the device to the
read mode (or erase-suspend-read mode if the device was in Erase Suspend).
Note that if DQ1 goes high during a Write Buffer Programming operation, the system must write the Write-to-
Buffer-Abort Reset command sequence to reset the device for the next operation.
相關PDF資料 |
PDF描述 |
|---|---|
| S29GL128N11FFIVH2 | 16M X 16 FLASH 3V PROM, 110 ns, PBGA64 |
| S29JL032J70TFI213 | 2M X 16 FLASH 3V PROM, 70 ns, PDSO48 |
| S29PL032J65BFI150 | 2M X 16 FLASH 3V PROM, 65 ns, PBGA56 |
| S29PL127J70BFI000 | 8M X 16 FLASH 3V PROM, 70 ns, PBGA80 |
| S29XS064R0PBHW010 | 4M X 16 FLASH 1.8V PROM, 80 ns, PBGA44 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S29GL128N11FFA010 | 制造商:Spansion 功能描述: |
| S29GL128N11FFA013 | 制造商:Spansion 功能描述: |
| S29GL128N11FFI010 | 制造商:Spansion 功能描述:Flash - NOR IC |
| S29GL128N11FFI020 | 制造商:Spansion 功能描述: 制造商:Spansion 功能描述:Flash - NOR IC |
| S29GL128N11FFIIH0 | 制造商:Spansion 功能描述:NOR Flash Parallel 3V/3.3V 128Mbit 16M/8M x 8bit/16bit 110ns 64-Pin Fortified BGA Tray |
發布緊急采購，3分鐘左右您將得到回復。