參數資料
型號： S29GL064A10BAIW12
廠商： SPANSION LLC
元件分類： PROM
英文描述： 4M X 16 FLASH 3V PROM, 100 ns, PBGA64
封裝： FBGA-64
文件頁數： 49/97頁
文件大?。?/td> 3490K
代理商： S29GL064A10BAIW12
January 11, 2006 S29GL-A_00_A5
S29GL-A MirrorBit Flash Family
51
Pr el im i n a r y
If DQ5 goes high during a program or erase operation, writing the reset com-
mand returns the device to the read mode (or erase-suspend-read mode if the
device was in Erase Suspend).
Note that if DQ1 goes high during a Write Buffer Programming operation, the
system must write the Write-to-Buffer-Abort Reset command sequence to reset
the device for the next operation.
Autoselect Command Sequence
The autoselect command sequence allows the host system to read several iden-
tifier codes at specific addresses:
Note: The device ID is read over three cycles. SA = Sector Address
The autoselect command sequence is initiated by first writing two unlock cycles.
This is followed by a third write cycle that contains the autoselect command. The
device then enters the autoselect mode. The system may read at any address
any number of times without initiating another autoselect command sequence:
The system must write the reset command to return to the read mode (or erase-
suspend-read mode if the device was previously in Erase Suspend).
Enter/Exit Secured Silicon Sector Command Sequence
The Secured Silicon Sector region provides a secured data area containing an
8-word/16-byte random Electronic Serial Number (ESN). The system can access
the Secured Silicon Sector region by issuing the three-cycle Enter Secured Sili-
con Sector command sequence. The device continues to access the Secured
Silicon Sector region until the system issues the four-cycle Exit Secured Silicon
Sector command sequence. The Exit Secured Silicon Sector command sequence
returns the device to normal operation. Table 30 on page 61 and Table 31 on
page 62 show the address and data requirements for both command sequences.
formation. Note that the ACC function and unlock bypass modes are not available
when the Secured Silicon Sector is enabled.
Word Program Command Sequence
Programming is a four-bus-cycle operation. The program command sequence is
initiated by writing two unlock write cycles, followed by the program set-up com-
mand. The program address and data are written next, which in turn initiate the
Embedded Program algorithm. The system is not required to provide further
controls or timings. The device automatically provides internally generated pro-
gram pulses and verifies the programmed cell margin. Table 30 on page 61 and
Table 31 on page 62 show the address and data requirements for the word pro-
gram command sequence, respectively.
Identifier Code
A7:A0
(x16)
A6:A-1
(x8)
Manufacturer ID
00h
Device ID, Cycle 1
01h
02h
Device ID, Cycle 2
0Eh
1Ch
Device ID, Cycle 3
0Fh
1Eh
Secured Silicon Sector Factory Protect
03h
06h
Sector Protect Verify
(SA)02h
(SA)04h
相關PDF資料
PDF描述
S29GL128N11FAIVH0 16M X 16 FLASH 3V PROM, 110 ns, PBGA64
S29GL128N11FFIVH2 16M X 16 FLASH 3V PROM, 110 ns, PBGA64
S29JL032J70TFI213 2M X 16 FLASH 3V PROM, 70 ns, PDSO48
S29PL032J65BFI150 2M X 16 FLASH 3V PROM, 65 ns, PBGA56
S29PL127J70BFI000 8M X 16 FLASH 3V PROM, 70 ns, PBGA80
相關代理商/技術參數
參數描述
S29GL064A10FAIR10 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 64MBIT 8MX8/4MX16 100NS 64BGA - Trays
S29GL064A10FAIR50 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 64MBIT 4MX16 100NS 64BGA - Trays
S29GL064A10FFIR30 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 64MBIT 8MX8/4MX16 100NS 64BGA - Trays
S29GL064A10TAIR42 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 64MBIT 8MX8/4MX16 100NS 48TSOP - Tape and Reel
S29GL064A10TAIR60 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 64MBIT 4MX16 100NS 48TSOP - Trays
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*