- 您現在的位置：買賣IC網 > PDF目錄98068 > S1C63408F0A0100 MICROCONTROLLER, PQFP128 PDF資料下載
參數資料
| 型號： | S1C63408F0A0100 |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | MICROCONTROLLER, PQFP128 |
| 封裝： | PLASTIC, QFP-128 |
| 文件頁數： | 65/151頁 |
| 文件大?。?/td> | 1171K |
| 代理商： | S1C63408F0A0100 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁當前第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁
12
EPSON
S1C63406/408 TECHNICAL MANUAL
CHAPTER 2: POWER SUPPLY AND INITIAL RESET
2.1.1 Voltage <VD1> for internal circuits
VD1 is the voltage for the OSC3 oscillation circuit and the internal logic circuits, and is generated by the
internal logic system voltage regulator.
The S1C63406/408 is designed with twin clock specification; it has two types of oscillation circuits OSC1
and OSC3 built-in. Use OSC1 clock for normal operation, and switch it to OSC3 by the software when
high-speed operation is necessary. When switching the clock, the operating voltage VD1 must be switched
by the software to stabilize the operation of the oscillation circuit and internal circuits.
The internal logic system voltage regulator can output the following four types of VD1 voltage. It should
be set at the value according to the oscillation circuit and oscillation frequency by the software.
VD1 = 1.1 V for low-power operation (when OSC3 oscillation is OFF)
VD1 = 1.3 V for high-speed operation (when Max. 700 kHz OSC3 CR oscillation is ON)
VD1 = 1.5 V for high-speed operation (when Max. 2.2 MHz OSC3 CR oscillation is ON)
VD1 = 1.7 V for high-speed operation (when Max. 4.2 MHz OSC3 crystal/ceramic/CR oscillation is ON)
Refer to Section 4.3, "Oscillation Circuit", for the VD1 switching procedure.
2.1.2 Voltage <VOSC> for OSC1 oscillation circuit
VOSC is the voltage for the OSC1 oscillation circuit and is generated by the oscillation system voltage
regulator for stabilizing the oscillation.
2.1.3 Voltage <VC1, VC2, VC4, VC5> for LCD driving
VC1, VC2, VC4 and VC5 are the LCD drive voltages generated by the LCD system voltage circuit. These
four output voltages can only be supplied to the externally expanded LCD driver.
The LCD system voltage circuit generates VC1 or VC2 with the voltage regulator built-in, and generates
three other voltages by boosting or reducing the voltage of VC1 or VC2. Table 2.1.3.1 shows the VC1, VC2,
VC4 and VC5 voltage values and boost/reduce status.
Table 2.1.3.1 LCD drive voltage when generated internally
LCD drive voltage
VC1 (0.975–1.2 V)
VC2 (1.950–2.4 V)
VC4 (2.925–3.6 V)
VC5 (3.900–4.8 V)
VDD = 1.3–3.6 V
VC1 (standard)
2
× VC1
3
× VC1
4
× VC1
VDD = 2.5–3.6 V
1/2
× VC2
VC2 (standard)
3/2
× VC2
2
× VC2
Note: The LCD drive voltage can be adjusted by the software (see Section 4.7.5). Values in the above
table are typical values.
Either the VC1 or VC2 used for the standard is selected according to the supply voltage by the software.
The VC2 standard improves the display quality and reduces current consumption, however, the power
supply voltage VDD must be 2.5 V or more.
Refer to Section 4.7, "LCD Driver", for control of the LCD drive voltage.
相關PDF資料 |
PDF描述 |
|---|---|
| S1C63406D0A0100 | MICROCONTROLLER, UUC103 |
| S1C63455F | 4-BIT, MROM, 4.1 MHz, MICROCONTROLLER, PQFP128 |
| S1C63455D | 4-BIT, MROM, 4.1 MHz, MICROCONTROLLER, UUC105 |
| S1C63458F0A0100 | MICROCONTROLLER, PQFP144 |
| S1C63466D | 4-BIT, MROM, 4.1 MHz, MICROCONTROLLER, UUC140 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S1C63557D04Q000 | 制造商:Seiko Instruments Inc (SII) 功能描述:EPSON MCU 4BIT |
| S1C63567 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63616 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63632 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63653 | 制造商:EPSON 制造商全稱:EPSON 功能描述:CMOS 4-bit Single Chip Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。