參數資料
型號： PIC18LF96J65-I/PT
廠商： Microchip Technology
文件頁數： 28/131頁
文件大?。?/td> 0K
描述： IC PIC MCU FLASH 48KX16 100TQFP
標準包裝： 90
系列： PIC® 18F
核心處理器： PIC
芯體尺寸： 8-位
速度： 41.667MHz
連通性： EBI/EMI，以太網，I²C，SPI，UART/USART
外圍設備： 欠壓檢測/復位，POR，PWM，WDT
輸入/輸出數： 70
程序存儲器容量： 96KB（48K x 16）
程序存儲器類型： 閃存
RAM 容量： 3808 x 8
電壓 - 電源 (Vcc/Vdd)： 2 V ~ 3.6 V
數據轉換器： A/D 16x10b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 100-TQFP
包裝： 托盤
2011 Microchip Technology Inc.
DS39762F-page 123
PIC18F97J60 FAMILY
8.7
8-Bit Data Width Mode
In 8-Bit Data Width mode, the external memory bus
operates only in Multiplexed mode; that is, data shares
the eight Least Significant bits of the address bus.
Figure 8-6 shows an example of 8-Bit Multiplexed mode
for 100-pin devices. This mode is used for a single 8-bit
memory connected for 16-bit operation. The instructions
will be fetched as two 8-bit bytes on a shared
data/address bus. The two bytes are sequentially
fetched within one instruction cycle (TCY). Therefore, the
designer must choose external memory devices accord-
ing to timing calculations based on 1/2 TCY (2 times the
instruction rate). For proper memory speed selection,
glue logic propagation delay times must be considered,
along with setup and hold times.
The Address Latch Enable (ALE) pin indicates that the
address bits, AD<15:0>, are available in the external
memory interface bus. The Output Enable signal (OE)
will enable one byte of program memory for a portion of
the instruction cycle, then BA0 will change and the
second byte will be enabled to form the 16-bit instruc-
tion word. The Least Significant bit of the address, BA0,
must be connected to the memory devices in this
mode. The Chip Enable signal (CE) is active at any
time that the microcontroller accesses external
memory, whether reading or writing. It is inactive
(asserted high) whenever the device is in Sleep mode.
This process generally includes basic EPROM and
Flash devices. It allows table writes to byte-wide
external memories.
During a TBLWT instruction cycle, the TABLAT data is
presented on the upper and lower bytes of the
AD<15:0> bus. The appropriate level of the BA0 control
line is strobed on the LSb of the TBLPTR.
FIGURE 8-6:
8-BIT MULTIPLEXED MODE EXAMPLE
AD<7:0>
A<19:16>(1)
ALE
D<15:8>
373
A<19:0>
A<x:1>
D<7:0>
OE
WR(2)
CE
Note
1:
The upper order address bits are used only for 20-bit address width. The upper AD byte is used
for all address widths except 8-bit.
2:
This signal only applies to table writes. See Section 7.1 “Table Reads and Table Writes”.
WRL
D<7:0>
PIC18F97J60
AD<15:8>(1)
Address Bus
Data Bus
Control Lines
CE
A0
BA0
相關PDF資料
PDF描述
PIC24F16KL401-I/P IC MCU 16BIT 16KB FLASH 20-PDIP
PIC24FJ128GA010-I/PF IC PIC MCU FLASH 128KB 100TQFP
PIC24FJ256GA110-I/PF IC PIC MCU FLASH 256K 100TQFP
PIC24FJ256GB110-I/PF IC PIC MCU FLASH 256K 100TQFP
PIC24FJ64GA004-E/ML IC PIC MCU FLASH 64K 44-QFN
相關代理商/技術參數
參數描述
PIC1-R68-JT 制造商:RCD 制造商全稱:RCD COMPONENTS INC. 功能描述:SURFACE MOUNT POWER INDUCTORS
PIC1-R68-JTQ 制造商:RCD 制造商全稱:RCD COMPONENTS INC. 功能描述:SURFACE MOUNT POWER INDUCTORS
PIC1-R68-JTW 制造商:RCD 制造商全稱:RCD COMPONENTS INC. 功能描述:SURFACE MOUNT POWER INDUCTORS
PIC1-R68-KT 制造商:RCD 制造商全稱:RCD COMPONENTS INC. 功能描述:SURFACE MOUNT POWER INDUCTORS
PIC1-R68-KTQ 制造商:RCD 制造商全稱:RCD COMPONENTS INC. 功能描述:SURFACE MOUNT POWER INDUCTORS
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*