- 您現在的位置：買賣IC網 > PDF目錄1965 > PIC18LF96J65-I/PT (Microchip Technology)IC PIC MCU FLASH 48KX16 100TQFP PDF資料下載
參數資料
| 型號： | PIC18LF96J65-I/PT |
| 廠商： | Microchip Technology |
| 文件頁數： | 109/131頁 |
| 文件大小： | 0K |
| 描述： | IC PIC MCU FLASH 48KX16 100TQFP |
| 標準包裝： | 90 |
| 系列： | PIC® 18F |
| 核心處理器： | PIC |
| 芯體尺寸： | 8-位 |
| 速度： | 41.667MHz |
| 連通性： | EBI/EMI，以太網，I²C，SPI，UART/USART |
| 外圍設備： | 欠壓檢測/復位，POR，PWM，WDT |
| 輸入/輸出數： | 70 |
| 程序存儲器容量： | 96KB（48K x 16） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 3808 x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 2 V ~ 3.6 V |
| 數據轉換器： | A/D 16x10b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 100-TQFP |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁當前第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁
2011 Microchip Technology Inc.
DS39762F-page 79
PIC18F97J60 FAMILY
6.1.3
PIC18F9XJ60/9XJ65 PROGRAM
MEMORY MODES
The 100-pin devices in this family can address up to a
total of 2 Mbytes of program memory. This is achieved
through the external memory bus. There are two
distinct operating modes available to the controllers:
Microcontroller (MC)
Extended Microcontroller (EMC)
The program memory mode is determined by setting
the EMB Configuration bits (CONFIG3L<5:4>), as
shown in Register 6-1. (Also see Section 25.1
for additional details on the
device Configuration bits).
The program memory modes operate as follows:
The Microcontroller Mode accesses only on-chip
Flash memory. Attempts to read above the top of
on-chip memory causes a read of all ‘0’s (a NOP
instruction).
The Microcontroller mode is also the only operating
mode available to 64-pin and 80-pin devices.
The Extended Microcontroller Mode allows
access to both internal and external program
memories as a single block. The device can
access its entire on-chip program memory. Above
this, the device accesses external program
memory up to the 2-Mbyte program space limit.
Execution automatically switches between the
two memories as required.
The setting of the EMB Configuration bits also controls
the address bus width of the external memory bus. This
is covered in more detail in Section 8.0 “External
.
In all modes, the microcontroller has complete access
to data RAM.
Figure 6-3 compares the memory maps of the different
program memory modes. The differences between
on-chip and external memory access limitations are
more fully explained in Table 6-2.
REGISTER 6-1:
CONFIG3L: CONFIGURATION REGISTER 3 LOW
R/WO-1
U-0
WAIT(1)
BW(1)
EMB1(1)
EMB0(1)
EASHFT(1)
—
bit 7
bit 0
Legend:
R = Readable bit
WO = Write-Once bit
U = Unimplemented bit, read as ‘0’
-n = Value when device is unprogrammed
‘1’ = Bit is set
‘0’ = Bit is cleared
bit 7
WAIT:
External Bus Wait Enable bit(1)
1
= Wait states for operations on external memory bus are disabled
0
= Wait states for operations on external memory bus are enabled and selected by MEMCON<5:4>
bit 6
BW:
Data Bus Width Select bit(1)
1
= 16-Bit Data Width mode
0
= 8-Bit Data Width mode
bit 5-4
EMB<1:0>:
External Memory Bus Configuration bits(1)
11
= Microcontroller mode, external bus disabled
10
= Extended Microcontroller mode,12-Bit Addressing mode
01
= Extended Microcontroller mode,16-Bit Addressing mode
00
= Extended Microcontroller mode, 20-Bit Addressing mode
bit 3
EASHFT:
External Address Bus Shift Enable bit(1)
1
= Address shifting is enabled; address on external bus is offset to start at 000000h
0
= Address shifting is disabled; address on external bus reflects the PC value
bit 2-0
Unimplemented:
Read as ‘0’
Note 1:
Implemented on 100-pin devices only.
相關PDF資料 |
PDF描述 |
|---|---|
| PIC24F16KL401-I/P | IC MCU 16BIT 16KB FLASH 20-PDIP |
| PIC24FJ128GA010-I/PF | IC PIC MCU FLASH 128KB 100TQFP |
| PIC24FJ256GA110-I/PF | IC PIC MCU FLASH 256K 100TQFP |
| PIC24FJ256GB110-I/PF | IC PIC MCU FLASH 256K 100TQFP |
| PIC24FJ64GA004-E/ML | IC PIC MCU FLASH 64K 44-QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PIC1-R68-JT | 制造商:RCD 制造商全稱:RCD COMPONENTS INC. 功能描述:SURFACE MOUNT POWER INDUCTORS |
| PIC1-R68-JTQ | 制造商:RCD 制造商全稱:RCD COMPONENTS INC. 功能描述:SURFACE MOUNT POWER INDUCTORS |
| PIC1-R68-JTW | 制造商:RCD 制造商全稱:RCD COMPONENTS INC. 功能描述:SURFACE MOUNT POWER INDUCTORS |
| PIC1-R68-KT | 制造商:RCD 制造商全稱:RCD COMPONENTS INC. 功能描述:SURFACE MOUNT POWER INDUCTORS |
| PIC1-R68-KTQ | 制造商:RCD 制造商全稱:RCD COMPONENTS INC. 功能描述:SURFACE MOUNT POWER INDUCTORS |
發布緊急采購，3分鐘左右您將得到回復。