參數資料
型號： PCF8584
廠商： NXP Semiconductors N.V.
英文描述： IIC-bus controller(IIC總線控制器)
中文描述： IIC總線控制器（國際進口總線控制器）
文件頁數： 13/40頁
文件大小： 224K
代理商： PCF8584
1997 Oct 21
13
Philips Semiconductors
Product specification
I
2
C-bus controller
PCF8584
6.8.2.7
BB
‘Bus Busy’ bit. This is a read-only flag indicating when the
I
2
C-bus is in use. A zero indicates that the bus is busy, and
access is not possible. This bit is set/reset (logic 1/logic 0)
by STOP/START conditions.
6.9
Multi-master operation
To avoid conflict between data and repeated START and
STOP operations, multi-master systems have some
limitations:
When powering up multiple PCF8584s in multi-master
systems, the possibility exists that one node may power
up slightly after another node has already begun an
I
2
C-bus transmission; the Bus Busy condition will thus
not have been detected. To avoid this condition, a delay
should be introduced in the initialization sequence of
each PCF8584 equal to the longest I
2
C-bus
transmission, see flowchart ‘PCF8584 initialization’
(Fig.5).
6.10
Reset
A LOW level pulse on the RESET (CLK must run) input
forces the I
2
C-bus controller into a well-defined state.
All flags in S1 are reset to logic 0, except the PIN flag and
the BB flag, which are set to logic 1. S0' and S3 are set
to 00H.
The RESET pin is also used for the STROBE output
signal. Both functions are separated on-chip by a digital
filter. The reset input signal has to be sufficiently long
(minimum 30 clock cycles) to pass through the filter.
The STROBE output signal is sufficiently short (8 clock
cycles) to be blocked by the filter. For more detailed
information on the strobe function see Section 6.12.
6.11
Comparison to the MAB8400 I
2
C-bus interface
The structure of the PCF8584 is similar to that of the
MAB8400 series of microcontrollers, but with a modified
control structure. Access to all I
2
C-bus control and status
registers is done via the parallel-bus port in conjunction
with register select input A0, and control bits ESO, ES1
and ES2.
6.11.1
D
ELETED FUNCTIONS
The following functions are not available in the PCF8584:
Always selected (ALS flag)
Access to the bit counter (BC0 to BC2)
Full SCL frequency selection (2 bits instead of 5 bits)
The non-acknowledge mode (ACK flag)
Asymmetrical clock (ASC flag).
6.11.2
ADDED FUNCTIONS
The following functions either replace the deleted
functions or are completely new:
Chip clock prescaler
Assert acknowledge bit (ACK flag)
Register selection bits (ES1 and ES2 flags)
Additional status flags (BER, ‘bus error’)
Automatic interface control between 80XX and
68000-type microcontrollers
Programmable interrupt vector
Strobe generator
Bus monitor function
Long-distance mode [non-I
2
C-bus mode (4-wire); only
for communication between parallel-bus processors
using the PCF8584 at each interface point].
6.12
Special function modes
6.12.1
S
TROBE
When the I
2
C-bus controller receives its own address (or
the ‘00H’ general call address) followed immediately by a
STOP condition (i.e. no further data transmitted after the
address), a strobe output signal is generated at the
RESET/STROBE pin (pin 19). The STROBE signal
consists of a monostable output pulse (active LOW),
8 clock cycles long (see Fig.9). It is generated after the
STOP condition is received, preceded by the correct slave
address. This output can be used as a bus access
controller for multi-master parallel-bus systems.
相關PDF資料
PDF描述
PCF8593 Low power clock/calendar(低功耗時鐘/日歷)
PCF8801 CRYSTAL RESONATOR, 6MHZ
PCF8801U LCD driver for 140 x 2 segments
PCF8811 80 x 128 pixels matrix LCD driver
PCF8812 CRYSTAL, 8.0 MHZ
相關代理商/技術參數
參數描述
PCF8584P 制造商:NXP Semiconductors 功能描述:I2C Bus Controller 20-Pin PDIP Bulk
PCF8584P,112 功能描述:I2C 接口集成電路 PARALLEL TO I2C CONVERTER RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16
PCF8584P112 制造商:NXP Semiconductors 功能描述:PARALLEL TO I2C BUS INTERFACE 8584 制造商:NXP Semiconductors 功能描述:IC I2C CONTROLLER DIP-20
PCF8584PN 制造商:未知廠家 制造商全稱:未知廠家 功能描述:I/O Port
PCF8584T 制造商:NXP Semiconductors 功能描述: 制造商:Texas Instruments 功能描述: 制造商:NXP Semiconductors 功能描述:I2C Bus Controller 20-Pin SO 制造商:PHILIPS-SEMI 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*