參數資料
型號： PCF8584
廠商： NXP Semiconductors N.V.
英文描述： IIC-bus controller(IIC總線控制器)
中文描述： IIC總線控制器（國際進口總線控制器）
文件頁數： 12/40頁
文件大?。?/td> 224K
代理商： PCF8584
1997 Oct 21
12
Philips Semiconductors
Product specification
I
2
C-bus controller
PCF8584
6.8.2.1
PIN bit
‘Pending Interrupt Not’ (MSB of register S1) is a status flag
which is used to synchronize serial communication and is
set to logic 0 whenever the PCF8584 requires servicing.
The PIN bit is normally read in polled applications to
determine when an I
2
C-bus byte transmission/reception is
completed. The PIN bit may also be written, see
Section 6.8.1.
Each time a serial data transmission is initiated (by setting
the STA bit in the same register), the PIN bit will be set to
logic 1 automatically (inactive). When acting as
transmitter, PIN is also set to logic 1 (inactive) each time
S0 is written. In receiver mode, the PIN bit is automatically
set to logic 1 (inactive) each time the data register S0 is
read.
After transmission or reception of one byte on the I
2
C-bus
(9 clock pulses, including acknowledge), the PIN bit will be
automatically reset to logic 0 (active) indicating a complete
byte transmission/reception. When the PIN bit is
subsequently set to logic 1 (inactive), all status bits will be
reset to logic 0. PIN is also set to zero on a BER (bus error)
condition.
In polled applications, the PIN bit is tested to determine
when a serial transmission/reception has been completed.
When the ENI bit (bit 4 of write-only section of register S1)
is also set to logic 1 the hardware interrupt is enabled.
In this case, the PIN flag also triggers an external interrupt
(active LOW) via the INT output each time PIN is reset to
logic 0 (active).
When acting as slave transmitter or slave receiver, while
PIN = 0, the PCF8584 will suspend I
2
C-bus transmission
by holding the SCL line LOW until the PIN bit is set to
logic 1 (inactive). This prevents further data from being
transmitted or received until the current data byte in S0 has
been read (when acting as slave receiver) or the next data
byte is written to S0 (when acting as slave transmitter).
PIN bit summary:
The PIN bit can be used in polled applications to test
when a serial transmission has been completed. When
the ENI bit is also set, the PIN flag sets the external
interrupt via the INT output.
Setting the STA bit (start bit) will set PIN = 1 (inactive).
In transmitter mode, after successful transmission of
one byte on the I
2
C-bus the PIN bit will be automatically
reset to logic 0 (active) indicating a complete byte
transmission.
In transmitter mode, PIN is set to logic 1 (inactive) each
time register S0 is written.
In receiver mode, PIN is set to logic 0 (active) on
completion of each received byte. Subsequently, the
SCL line will be held LOW until PIN is set to logic 1.
In receiver mode, when register S0 is read, PIN is set to
logic 1 (inactive).
In slave receiver mode, an I
2
C-bus STOP condition will
set PIN = 0 (active).
PIN = 0 if a bus error (BER) occurs.
6.8.2.2
STS
When in slave receiver mode, this flag is asserted when an
externally generated STOP condition is detected (used
only in slave receiver mode).
6.8.2.3
BER
Bus error; a misplaced START or STOP condition has
been detected. Resets BB (to logic 1; inactive), sets
PIN = 0 (active).
6.8.2.4
LRB/AD0
‘Last Received Bit’ or ‘Address 0 (General Call) bit’. This
status bit serves a dual function, and is valid only while
PIN = 0:
1.
LRB holds the value of the last received bit over the
I
2
C-bus while AAS = 0 (not addressed as slave).
Normally this will be the value of the slave
acknowledgement; thus checking for slave
acknowledgement is done via testing of the LRB.
2.
AD0; when AAS = 1 (‘Addressed As Slave’ condition),
the I
2
C-bus controller has been addressed as a slave.
Under this condition, this bit becomes the ‘AD0’ bit and
will be set to logic 1 if the slave address received was
the ‘general call’ (00H) address, or logic 0 if it was the
I
2
C-bus controller’s own slave address.
6.8.2.5
AAS
‘Addressed As Slave’ bit. Valid only when PIN = 0. When
acting as slave receiver, this flag is set when an incoming
address over the I
2
C-bus matches the value in own
address register S0' (shifted by one bit, see Section 6.4),
or if the I
2
C-bus ‘General Call’ address (00H) has been
received (‘General Call’ is indicated when AD0 status bit is
also set to logic 1, see Section 6.8.2.4).
6.8.2.6
LAB
‘Lost Arbitration’ Bit. This bit is set when, in multi-master
operation, arbitration is lost to another master on the
I
2
C-bus.
相關PDF資料
PDF描述
PCF8593 Low power clock/calendar(低功耗時鐘/日歷)
PCF8801 CRYSTAL RESONATOR, 6MHZ
PCF8801U LCD driver for 140 x 2 segments
PCF8811 80 x 128 pixels matrix LCD driver
PCF8812 CRYSTAL, 8.0 MHZ
相關代理商/技術參數
參數描述
PCF8584P 制造商:NXP Semiconductors 功能描述:I2C Bus Controller 20-Pin PDIP Bulk
PCF8584P,112 功能描述:I2C 接口集成電路 PARALLEL TO I2C CONVERTER RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16
PCF8584P112 制造商:NXP Semiconductors 功能描述:PARALLEL TO I2C BUS INTERFACE 8584 制造商:NXP Semiconductors 功能描述:IC I2C CONTROLLER DIP-20
PCF8584PN 制造商:未知廠家 制造商全稱:未知廠家 功能描述:I/O Port
PCF8584T 制造商:NXP Semiconductors 功能描述: 制造商:Texas Instruments 功能描述: 制造商:NXP Semiconductors 功能描述:I2C Bus Controller 20-Pin SO 制造商:PHILIPS-SEMI 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*