- 您現在的位置：買賣IC網 > PDF目錄367820 > PCF8584 (NXP Semiconductors N.V.) IIC-bus controller(IIC總線控制器) PDF資料下載
參數資料
| 型號： | PCF8584 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | IIC-bus controller(IIC總線控制器) |
| 中文描述： | IIC總線控制器（國際進口總線控制器） |
| 文件頁數： | 10/40頁 |
| 文件大?。?/td> | 224K |
| 代理商： | PCF8584 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
1997 Oct 21
10
Philips Semiconductors
Product specification
I
2
C-bus controller
PCF8584
6.8.1
R
EGISTER
S1
CONTROL SECTION
The write-only section of S1 enables access to registers S0, S0', S1, S2 and S3, and controls I
2
C-bus operation; see
Table 4.
6.8.1.1
PIN (Pending Interrupt Not)
When the PIN bit is written with a logic 1, all status bits are reset to logic 0. This may serve as a software reset function
(see Figs 5 to 9). PIN is the only bit in S1 which may be both read and written to. PIN is mostly used as a status bit for
synchronizing serial communication, see Section 6.8.2.
6.8.1.2
ESO (Enable Serial Output)
ESO enables or disables the serial I
2
C-bus I/O. When ESO is LOW, register access for initialization is possible. When
ESO is HIGH, I
2
C-bus communication is enabled; communication with serial shift register S0 is enabled and the S1 bus
status bits are made available for reading.
Table 5
Register access control; ESO = 0 (serial interface off) and ESO = 1 (serial interface on)
Notes
1.
2.
With ESO = 0, bits ENI, STA, STO and ACK of S1 can be read for test purposes.
‘X’ if ENI = 0.
6.8.1.3
ES1 and ES2
ES1 and ES2 control selection of other registers for initialization and control of normal operation. After these bits are
programmed for access to the desired register (shown in Table 5), the register is selected by a logic LOW level on
register select pin A0.
6.8.1.4
ENI
This bit enables the external interrupt output INT, which is generated when the PIN bit is active (logic 0).
This bit must be set to logic 0 before entering the long-distance mode, and remain at logic 0 during operation in
long-distance mode.
INTERNAL REGISTER ADDRESSING 2-WIRE MODE
A0
ES1
ES2
IACK
FUNCTION
ESO = 0; serial interface off
(see note 1)
1
0
0
0
0
0
0
1
X
0
1
0
1
(2)
1
(2)
1
(2)
1
(2)
R/W S1: control
R/W S0': (own address)
R/W S3: (interrupt vector)
R/W S2: (clock register)
ESO = 1; serial interface on
1
1
0
0
X
0
0
0
0
0
X
X
0
1
X
1
1
1
1
0
W S1: control
R S1; status
R/W S0: (data)
R/W S3: (interrupt vector)
R S3: (interrupt vector ACK cycle))
相關PDF資料 |
PDF描述 |
|---|---|
| PCF8593 | Low power clock/calendar(低功耗時鐘/日歷) |
| PCF8801 | CRYSTAL RESONATOR, 6MHZ |
| PCF8801U | LCD driver for 140 x 2 segments |
| PCF8811 | 80 x 128 pixels matrix LCD driver |
| PCF8812 | CRYSTAL, 8.0 MHZ |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCF8584P | 制造商:NXP Semiconductors 功能描述:I2C Bus Controller 20-Pin PDIP Bulk |
| PCF8584P,112 | 功能描述:I2C 接口集成電路 PARALLEL TO I2C CONVERTER RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
| PCF8584P112 | 制造商:NXP Semiconductors 功能描述:PARALLEL TO I2C BUS INTERFACE 8584 制造商:NXP Semiconductors 功能描述:IC I2C CONTROLLER DIP-20 |
| PCF8584PN | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:I/O Port |
| PCF8584T | 制造商:NXP Semiconductors 功能描述: 制造商:Texas Instruments 功能描述: 制造商:NXP Semiconductors 功能描述:I2C Bus Controller 20-Pin SO 制造商:PHILIPS-SEMI 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。