- 您現在的位置：買賣IC網 > PDF目錄224596 > NAND01GR4B2BZA1F (STMICROELECTRONICS) 64M X 16 FLASH 1.8V PROM, 25000 ns, PBGA63 PDF資料下載
參數資料
| 型號： | NAND01GR4B2BZA1F |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | PROM |
| 英文描述： | 64M X 16 FLASH 1.8V PROM, 25000 ns, PBGA63 |
| 封裝： | 9 X 11 MM, 1 MM HEIGHT, 0.80 MM PITCH, LEAD FREE, VFBGA-63 |
| 文件頁數： | 9/63頁 |
| 文件大?。?/td> | 684K |
| 代理商： | NAND01GR4B2BZA1F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁
NAND01G-B2B, NAND02G-B2C
Signal descriptions
17/63
3.7
Write Enable (W)
The Write Enable input, W, controls writing to the Command Interface, Input Address and
Data latches. Both addresses and data are latched on the rising edge of Write Enable.
During power-up and power-down a recovery time of 10s (min) is required before the
Command Interface is ready to accept a command. It is recommended to keep Write Enable
high during the recovery time.
3.8
Write Protect (WP)
The Write Protect pin is an input that gives a hardware protection against unwanted program
or erase operations. When Write Protect is Low, VIL, the device does not accept any
program or erase operations.
It is recommended to keep the Write Protect pin Low, VIL, during power-up and power-down.
3.9
Ready/Busy (RB)
The Ready/Busy output, RB, is an open-drain output that can be used to identify if the P/E/R
Controller is currently active. When Ready/Busy is Low, VOL, a read, program or erase
operation is in progress. When the operation completes Ready/Busy goes High, VOH.
The use of an open-drain output allows the Ready/Busy pins from several memories to be
connected to a single pull-up resistor. A Low will then indicate that one, or more, of the
memories is busy.
Refer to the Section 11.1: Ready/Busy Signal electrical characteristics for details on how to
calculate the value of the pull-up resistor.
3.10
VDD Supply Voltage
VDD provides the power supply to the internal core of the memory device. It is the main
power supply for all operations (read, program and erase).
An internal voltage detector disables all functions whenever VDD is below VLKO (see
power-transitions.
Each device in a system should have VDD decoupled with a 0.1F capacitor. The PCB track
widths should be sufficient to carry the required program and erase currents.
3.11
VSS Ground
Ground, VSS, is the reference for the power supply. It must be connected to the system
ground.
相關PDF資料 |
PDF描述 |
|---|---|
| NAND08GR4B3AZB6 | 512M X 16 FLASH 1.8V PROM, 25000 ns, PBGA63 |
| NAND256W4A2AZA6E | 16M X 16 FLASH 3V PROM, 12000 ns, PBGA55 |
| NCP303LSN41T1 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
| NCS6416DWG | 8-CHANNEL, VIDEO MULTIPLEXER, PDSO20 |
| NCS6S4803L5C | 1-OUTPUT 5 W DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NAND01GR4B2BZA6 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:1 Gbit, 2 Gbit, 2112 Byte/1056 Word Page, 1.8V/3V, NAND Flash Memory |
| NAND01GR4B2BZA6E | 制造商:NUMONYX 制造商全稱:Numonyx B.V 功能描述:1-Gbit, 2-Gbit, 2112-byte/1056-word page, 1.8 V/3 V, NAND flash memory |
| NAND01GR4B2BZA6F | 制造商:NUMONYX 制造商全稱:Numonyx B.V 功能描述:1-Gbit, 2-Gbit, 2112-byte/1056-word page, 1.8 V/3 V, NAND flash memory |
| NAND01GR4B2BZB1 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:1 Gbit, 2 Gbit, 2112 Byte/1056 Word Page, 1.8V/3V, NAND Flash Memory |
| NAND01GR4B2BZB6 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:1 Gbit, 2 Gbit, 2112 Byte/1056 Word Page, 1.8V/3V, NAND Flash Memory |
發布緊急采購，3分鐘左右您將得到回復。