參數資料
型號： NAND01GR4B2BZA1F
廠商： STMICROELECTRONICS
元件分類： PROM
英文描述： 64M X 16 FLASH 1.8V PROM, 25000 ns, PBGA63
封裝： 9 X 11 MM, 1 MM HEIGHT, 0.80 MM PITCH, LEAD FREE, VFBGA-63
文件頁數： 19/63頁
文件大?。?/td> 684K
代理商： NAND01GR4B2BZA1F
Device operations
NAND01G-B2B, NAND02G-B2C
26/63
6.3
Page Program
The Page Program operation is the standard operation to program data to the memory
array. Generally, the page is programmed sequentially, however the device does support
Random Input within a page. It is recommended to address pages sequentially within a
given block.
The memory array is programmed by page, however partial page programming is allowed
where any number of Bytes (1 to 2112) or Words (1 to 1056) can be programmed.
The maximum number of consecutive partial page program operations allowed in the same
page is four. After exceeding this a Block Erase command must be issued before any further
program operations can take place in that page.
6.3.1
Sequential Input
To input data sequentially the addresses must be sequential and remain in one block.
For Sequential Input each Page Program operation consists of five steps (see Figure 9):
1.
one bus cycle is required to setup the Page Program (Sequential Input) command (see
2.
four or five bus cycles are then required to input the program address (refer to Table 6
3.
the data is then loaded into the Data Registers
4.
one bus cycle is required to issue the Page Program confirm command to start the
P/E/R Controller. The P/E/R will only start if the data has been loaded in step 3.
5.
the P/E/R Controller then programs the data into the array.
6.3.2
Random Data Input in a page
During a Sequential Input operation, the next sequential address to be programmed can be
replaced by a random address, by issuing a Random Data Input command. The following
two steps are required to issue the command:
1.
one bus cycle is required to setup the Random Data Input command (see Table 10)
2.
two bus cycles are then required to input the new column address (refer to Table 6)
Random Data Input can be repeated as often as required in any given page.
Once the program operation has started the Status Register can be read using the Read
Status Register command. During program operations the Status Register will only flag
errors for bits set to '1' that have not been successfully programmed to '0'.
During the program operation, only the Read Status Register and Reset commands will be
accepted, all other commands will be ignored.
Once the program operation has completed the P/E/R Controller bit SR6 is set to ‘1’ and the
Ready/Busy signal goes High.
The device remains in Read Status Register mode until another valid command is written to
the Command Interface.
相關PDF資料
PDF描述
NAND08GR4B3AZB6 512M X 16 FLASH 1.8V PROM, 25000 ns, PBGA63
NAND256W4A2AZA6E 16M X 16 FLASH 3V PROM, 12000 ns, PBGA55
NCP303LSN41T1 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5
NCS6416DWG 8-CHANNEL, VIDEO MULTIPLEXER, PDSO20
NCS6S4803L5C 1-OUTPUT 5 W DC-DC REG PWR SUPPLY MODULE
相關代理商/技術參數
參數描述
NAND01GR4B2BZA6 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:1 Gbit, 2 Gbit, 2112 Byte/1056 Word Page, 1.8V/3V, NAND Flash Memory
NAND01GR4B2BZA6E 制造商:NUMONYX 制造商全稱:Numonyx B.V 功能描述:1-Gbit, 2-Gbit, 2112-byte/1056-word page, 1.8 V/3 V, NAND flash memory
NAND01GR4B2BZA6F 制造商:NUMONYX 制造商全稱:Numonyx B.V 功能描述:1-Gbit, 2-Gbit, 2112-byte/1056-word page, 1.8 V/3 V, NAND flash memory
NAND01GR4B2BZB1 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:1 Gbit, 2 Gbit, 2112 Byte/1056 Word Page, 1.8V/3V, NAND Flash Memory
NAND01GR4B2BZB6 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:1 Gbit, 2 Gbit, 2112 Byte/1056 Word Page, 1.8V/3V, NAND Flash Memory
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*