- 您現在的位置：買賣IC網 > PDF目錄384760 > MT90820 (Mitel Networks Corporation) Large Digital Switch(大數字開關) PDF資料下載
參數資料
| 型號： | MT90820 |
| 廠商： | Mitel Networks Corporation |
| 英文描述： | Large Digital Switch(大數字開關) |
| 中文描述： | 大型數字交換（大數字開關） |
| 文件頁數： | 12/33頁 |
| 文件大小： | 132K |
| 代理商： | MT90820 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
MT90820
CMOS
12
Table 8 - Interface Mode Selection (IMS) Register Bits
Table 9 - Serial Data Rate Selection (16 input x 16 output)
Bit
Name
Description
15-10
Unused
Must be zero for normal operation.
9-5
BPD4-0
Block Programming Data.
These bits carry the value to be loaded into the
connection memory block whenever the memory block programming feature is
activated. After the MBP bit in the control register is set to 1 and the BPE bit is set to
1, the contents of the bits BPD4- 0 are loaded into bit 15 to bit 11 of the connection
memory. Bit 10 to bit 0 of the connection memory are set to 0.
4
BPE
Begin Block programming Enable.
A zero to one transition of this bit enables the
memory block programming function. The BPE and BPD4-0 bits in the IMS register
have to be defined in the same write operation. Once the BPE bit is set high, the
device requires two frames to complete the block programming. After the
programming function has finished, the BPE bit returns to zero to indicate the
operation is completed. When the BPE = 1, the BPE or MBP can be set to 0 to abort
the programming operation.
When BPE = 1, the other bits in the IMS register must not be changed for two frames
to ensure proper operation.
3
OSB
Output Stand By.
When ODE = 0 and OSB = 0, the output drivers of STo0 to STo15
are in high impedance mode. When ODE = 0 and OSB = 1, the output driver of STo0
to STo15 function normally. When ODE = 1, STo0 to STo15 output drivers function
normally.
2
SFE
Start Frame Evaluation.
A zero to one transition in this bit starts the frame evaluation
procedure. When the CFE bit in the FAR register changes from zero to one, the
evaluation procedure stops. To start another frame evaluation cycle, set this bit to zero
for at least one frame.
1 - 0
DR1-0
Data Rate Select.
Input/Output data rate selection. See Table 9 for detailed
programming.
DR1
DR0
Data Rate Selected
Master Clock Required
0
0
2.048 Mb/s
4.096 MHz
0
1
4.096 Mb/s
8.192 MHz
1
0
8.192 Mb/s
16.384 MHz
1
1
Reserved
Reserved
Read/Write Address:
Reset Value:
01
H
,
0000
H
.
7
6
5
4
3
2
1
0
8
9
10
11
12
13
DR0
DR1
BPD
1
BPD
2
BPD
3
0
14
15
BPD
0
0
BPD
4
BPE
OSB
SFE
0
0
0
0
相關PDF資料 |
PDF描述 |
|---|---|
| MT90823 | 3V Large Digital Switch(3V 大數字開關) |
| MT90826 | Quad Digital Switch(四數字開關) |
| MT90840 | Distributed Hyperchannel Switch(分布式超級通道開關) |
| MT90863AL1 | 3V Rate Conversion Digital Switch |
| MT90863 | 3V Rate Conversion Digital Switch(3V 速率轉換數字開關) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT90820AL | 制造商:Microsemi Corporation 功能描述:SWIT FABRIC 2K X 2K/1K X 1K/512 X 512 131.072MBPS 5V 100MQFP - Trays |
| MT90820AL1 | 制造商:Microsemi Corporation 功能描述:SWIT FABRIC 2K X 2K/1K X 1K/512 X 512 131.072MBPS 5V 100MQFP - Trays 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC DGTL SWITCH 2048X2048 100MQFP 制造商:Microsemi Corporation 功能描述:IC DGTL SWITCH 2048X2048 100MQFP |
| MT90820AP | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Large Digital Switch |
| MT90820AP1 | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Large Digital Switch |
| MT90820APR | 制造商:Microsemi Corporation 功能描述:SWIT FABRIC 2K X 2K/1K X 1K/512 X 512 5V 84PLCC - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。