參數資料
型號： MT48LC64M4A2
廠商： Micron Technology, Inc.
英文描述： SYNCHRONOUS DRAM
中文描述： 同步DRAM
文件頁數： 26/62頁
文件大?。?/td> 1517K
代理商： MT48LC64M4A2
26
256Mb: x4, x8, x16 SDRAM
256MSDRAM_E.p65
–
Rev. E; Pub. 3/02
Micron Technology, Inc., reserves the right to change products or specifications without notice.
2002, Micron Technology, Inc.
256Mb: x4, x8, x16
SDRAM
requires a
t
WR of at least one clock plus time, regardless
of frequency. In addition, when truncating a WRITE
burst, the DQM signal must be used to mask input data
for the clock edge prior to, and the clock edge coinci-
dent with, the PRECHARGE command. An example is
shown in Figure 18. Data
n
+ 1 is either the last of a burst
of two or the last desired of a longer burst. Following the
PRECHARGE command, a subsequent command to
the same bank cannot be issued until
t
RP is met. The
precharge can be issued coincident with the first coin-
cident clock edge (T2 in Figure 18) on an A1 Version and
with the second clock on an A2 Version (Figure 18.)
In the case of a fixed-length burst being executed to
completion, a PRECHARGE command issued at the
optimum time (as described above) provides the same
operation that would result from the same fixed-length
burst with auto precharge. The disadvantage of the
PRECHARGE command is that it requires that the com-
mand and address buses be available at the appropri-
ate time to issue the command; the advantage of the
PRECHARGE command is that it can be used to trun-
cate fixed-length or full-page bursts.
Figure 18
WRITE to PRECHARGE
DON
’
T CARE
DQM
CLK
DQ
T2
T1
T4
T3
T0
COMMAND
ADDRESS
BANK
a
,
COL
n
T5
NOP
WRITE
PRECHARGE
NOP
NOP
D
IN
n
D
IN
n
+ 1
ACTIVE
tRP
BANK
(
a
or all)
t
WR
BANK
a
,
ROW
DQM
DQ
COMMAND
ADDRESS
BANK
a
,
COL
n
NOP
WRITE
PRECHARGE
NOP
NOP
D
IN
n
D
IN
n
+ 1
ACTIVE
tRP
BANK
(
a
or all)
t
WR
NOTE:
DQM could remain LOW in this example if the WRITE burst is a fixed length of two.
BANK
a
,
ROW
T6
NOP
NOP
tWR @ tCLK
≥
15ns
tWR = tCLK < 15ns
Data for any WRITE burst may be truncated with a
subsequent READ command, and data for a fixed-
length WRITE burst may be immediately followed by a
READ command. Once the READ command is regis-
tered, the data inputs will be ignored, and WRITEs will
not be executed. An example is shown in Figure 17.
Data
n
+ 1 is either the last of a burst of two or the last
desired of a longer burst.
Data for a fixed-length WRITE burst may be fol-
lowed by, or truncated with, a PRECHARGE command
to the same bank (provided that auto precharge was
not activated), and a full-page WRITE burst may be
truncated with a PRECHARGE command to the same
bank. The PRECHARGE command should be issued
t
WR after the clock edge at which the last desired input
data element is registered. The auto precharge mode
Figure 17
WRITE to READ
CLK
DQ
T2
T1
T3
T0
COMMAND
ADDRESS
NOP
WRITE
BANK,
COL
n
D
IN
n
D
IN
n
+ 1
D
OUT
b
READ
NOP
NOP
BANK,
COL
b
NOP
D
OUT
b
+ 1
T4
T5
NOTE:
The WRITE command may be to any bank, and the READ command
may be to any bank. DQM is LOW. CAS latency = 2 for illustration.
Figure 16
Random WRITE Cycles
CLK
DQ
D
IN
n
T2
T1
T3
T0
COMMAND
ADDRESS
WRITE
BANK,
COL
n
D
IN
a
D
IN
x
D
IN
m
WRITE
WRITE
WRITE
BANK,
COL
a
BANK,
COL
x
BANK,
COL
m
NOTE:
Each WRITE command may be to any bank. DQM is LOW.
相關PDF資料
PDF描述
MT48LC4M32B2 SYNCHRONOUS DRAM
MT48LC4M32LFFC SYNCHRONOUS DRAM
MT48LC64M8A2 SYNCHRONOUS DRAM
MT48LC32M16A2 SYNCHRONOUS DRAM
MT48LC8M16A2FB-75LIT SYNCHRONOUS DRAM
相關代理商/技術參數
參數描述
MT48LC64M4A2_03 制造商:MICRON 制造商全稱:Micron Technology 功能描述:SYNCHRONOUS DRAM 256Mb: x4, x8, x16 SDRAM
MT48LC64M4A2_99 制造商:MICRON 制造商全稱:Micron Technology 功能描述:Synchronous DRAM 256Mb: x4, x8, x16 SDRAM
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*