參數資料
型號： MC7445ARX933LG
廠商： 飛思卡爾半導體(中國)有限公司
英文描述： RISC Microprocessor Hardware Specifications
中文描述： RISC微處理器硬件規格
文件頁數： 55/64頁
文件大?。?/td> 1127K
代理商： MC7445ARX933LG
MPC7455 RISC Microprocessor Hardware Specifications, Rev. 4.1
Freescale Semiconductor
55
System Design Information
Wakefield Engineering
33 Bridge St.
Pelham, NH 03076
Internet: www.wakefield.com
603-635-5102
Ultimately, the final selection of an appropriate heat sink depends on many factors, such as thermal performance at
a given air velocity, spatial volume, mass, attachment method, assembly, and cost.
9.8.1 Internal Package Conduction Resistance
For the exposed-die packaging technology, shown in
Table 3
, the intrinsic conduction thermal resistance paths are
as follows:
The die junction-to-case (actually top-of-die since silicon die is exposed) thermal resistance
The die junction-to-ball thermal resistance
Figure 28
depicts the primary heat transfer path for a package with an attached heat sink mounted to a printed-circuit
board.
Figure 28. C4 Package with Heat Sink Mounted to a Printed-Circuit Board
Heat generated on the active side of the chip is conducted through the silicon, then through the heat sink attach
material (or thermal interface material), and finally to the heat sink where it is removed by forced-air convection.
Because the silicon thermal resistance is quite small, for a first-order analysis, the temperature drop in the silicon
may be neglected. Thus, the thermal interface material and the heat sink conduction/convective thermal resistances
are the dominant terms.
9.8.2 Thermal Interface Materials
A thermal interface material is recommended at the package lid-to-heat sink interface to minimize the thermal
contact resistance. For those applications where the heat sink is attached by spring clip mechanism,
Figure 29
shows
the thermal performance of three thin-sheet thermal-interface materials (silicone, graphite/oil, floroether oil), a bare
joint, and a joint with thermal grease as a function of contact pressure. As shown, the performance of these thermal
interface materials improves with increasing contact pressure. The use of thermal grease significantly reduces the
External Resistance
(Note the internal versus external package resistance.)
External Resistance
Internal Resistance
Radiation
Convection
Radiation
Convection
Heat Sink
Printed-Circuit Board
Thermal Interface Material
Package/Leads
Die Junction
Die/Package
相關PDF資料
PDF描述
MC7445ARX867LF RISC Microprocessor Hardware Specifications
MC9328MXL i.MX Integrated Portable System Processor
MRF18030BLSR3 RF Power Field Effect Transistors N-Channel Enhancement-Mode Lateral MOSFETs
MW6S004NT1_07 RF Power Field Effect Transistor
MC9328MXLCVP15 i.MX Integrated Portable System Processor
相關代理商/技術參數
參數描述
MC7447A 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:PowerPC microprocessor
MC7447AHX1000LB 功能描述:微處理器 - MPU APOLO7PM RV1.1 1.3V 105C RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
MC7447AHX1000NB 功能描述:微處理器 - MPU APOLO7PM RV1.1 1.1V 105C RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
MC7447AHX1000NBR 制造商:Freescale Semiconductor 功能描述:MPU MPC74XX RISC 32BIT 0.13UM 1GHZ 1.8V/2.5V 360FCCBGA - Tape and Reel
MC7447AHX1000PC 制造商:Freescale Semiconductor 功能描述:MPU MPC74XX RISC 32BIT 0.13UM 1GHZ 1.8V/2.5V 360FCCBGA - Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*