參數資料
型號： MC68L11F1CFN3
廠商： FREESCALE SEMICONDUCTOR INC
元件分類： 微控制器/微處理器
英文描述： 8-BIT, EEPROM, MICROCONTROLLER, PQCC68
封裝： PLASTIC, LCC-68
文件頁數： 37/174頁
文件大小： 981K
代理商： MC68L11F1CFN3
MC68HC11F1
ANALOG-TO-DIGITAL CONVERTER
MOTOROLA
TECHNICAL DATA
10-7
10.7 Operation in STOP and WAIT Modes
If a conversion sequence is in progress when either the STOP or WAIT mode is en-
tered, the conversion of the current channel is suspended. When the MCU resumes
normal operation, that channel is resampled and the conversion sequence is resumed.
As the MCU exits the WAIT mode, the A/D circuits are stable and valid results can be
obtained on the first conversion. However, in STOP mode, all analog bias currents are
disabled and it is necessary to allow a stabilization period when leaving the STOP
mode. If the STOP mode is exited with a delay (DLY = 1), there is enough time for
these circuits to stabilize before the first conversion. If the STOP mode is exited with
no delay (DLY bit in OPTION register = 0), allow 10 ms for the A/D circuitry to stabilize
to avoid invalid results.
10.8 A/D Control/Status Registers
All bits in this register can be read or written, except CCF (bit 7), which is a read-only
status indicator, and bit 6, which always reads as zero. Write to ADCTL to initiate a
conversion. To quit a conversion in progress, write to this register and a new conver-
sion sequence begins immediately.
CCF — Conversions Complete Flag
A read-only status indicator, this bit is set when all four A/D result registers contain val-
id conversion results. Each time the ADCTL register is overwritten, this bit is automat-
ically cleared to zero and a conversion sequence is started. In the continuous mode,
CCF is set at the end of the first conversion sequence.
Bit 6 — Not implemented
Always reads zero
SCAN — Continuous Scan Control
When this control bit is clear, the four requested conversions are performed once to
fill the four result registers. When this control bit is set, conversions continue in a
round-robin fashion with the result registers updated as data becomes available.
MULT — Multiple Channel/Single Channel Control
When this bit is clear, the A/D converter system is configured to perform four consec-
utive conversions on the single channel specified by the four channel select bits CD–
CA (bits [3:0] of the ADCTL register). When this bit is set, the A/D system is configured
to perform a conversion on each of four channels where each result register corre-
sponds to one channel.
ADCTL — A/D Control/Status
$1030
Bit 7
654321
Bit 0
CCF
—
SCAN
MULT
CD
CC
CB
CA
RESET:
1
0
IIIII
I
相關PDF資料
PDF描述
MC68HC11F1CFN3R2 8-BIT, EEPROM, 3 MHz, MICROCONTROLLER, PQCC68
MC68HC11F1CFN3R2 8-BIT, EEPROM, 3 MHz, MICROCONTROLLER, PQCC68
MC68SZ328VH66V 66 MHz, RISC PROCESSOR, PBGA196
MC74F2970N DRAM CONTROLLER, PDIP24
MC908GP32CFBR2 8-BIT, FLASH, 8.2 MHz, MICROCONTROLLER, PQFP44
相關代理商/技術參數
參數描述
MC68L11F1CFNE3 功能描述:8位微控制器 -MCU 8B MCU 1KRAM 512BYTES RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68L11K1FN2R2 制造商:Motorola Inc 功能描述:
MC68L11K1FUE2 功能描述:8位微控制器 -MCU 8B MCU L-VOLTAGE-EPP RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68L711E9FN2 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC68L711E9FNE2 功能描述:8位微控制器 -MCU 8B MCU LO VOLTAGE RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*