- 您現在的位置：買賣IC網 > PDF目錄97995 > L6470HTR (STMICROELECTRONICS) STEPPER MOTOR CONTROLLER, 7 A, PDSO28 PDF資料下載
參數資料
| 型號： | L6470HTR |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 運動控制電子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 7 A, PDSO28 |
| 封裝： | ROHS COMPLIANT, HTSSOP-28 |
| 文件頁數： | 22/64頁 |
| 文件大小： | 814K |
| 代理商： | L6470HTR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
L6470
Functional description
Doc ID 16737 Rev 2
29/64
6.17
BUSY\SYNC pin
This pin is an open drain output which can be used as busy or synchronization signal
according to SYNC_EN bit value (STEP_MODE register).
6.17.1
BUSY operation mode
The pin works as busy signal when SYNC_EN bit is set low (default condition). In this mode
the output is forced low while a constant speed, absolute positioning or motion command is
under execution. The BUSY pin is released when command has been executed (target
speed or target position reached). The STATUS register includes a BUSY flag that is the
BUSY pin mirror (see paragraph 9.1.22).
In case of daisy-chain configuration, BUSY pins of different ICs can be hard-wired to save
host controller GPIOs.
6.17.2
SYNC operation mode
The pin works as synchronization signal when SYNC_EN bit is set high. In this mode a step
clock signal is provided on output according to SYNC_SEL and STEP_SEL parameters
combination (see paragraph 9.1.19).
6.18
FLAG pin
By default an internal open drain transistor pulls the FLAG pin to ground when at least one
of the following conditions occurs:
●
Power-up or standby/reset exit,
●
Stall detection on A bridge,
●
Stall detection on B bridge,
●
Overcurrent detection,
●
Thermal warning,
●
Thermal shutdown,
●
UVLO,
●
Switch turn-on event,
●
Wrong command,
●
Non performable command.
It is possible to mask one or more alarm conditions by programming the ALARM_EN
register (see paragraph 9.1.20, Table 20). If the corresponding bit of ALARM_EN register is
low, the alarm condition is masked and it does not cause a FLAG pin transition; all other
actions imposed by alarm conditions are performed anyway. In case of daisy-chain
configuration, FLAG pins of different ICs can be or-wired to save host controller GPIOs.
相關PDF資料 |
PDF描述 |
|---|---|
| L6562DTR | 0.8 A POWER FACTOR CONTROLLER, PDSO8 |
| L6562D | 0.8 A POWER FACTOR CONTROLLER, PDSO8 |
| L6563HTR | POWER FACTOR CONTROLLER, PDSO16 |
| L6563H | POWER FACTOR CONTROLLER, PDSO16 |
| L6565N | 0.7 A SWITCHING CONTROLLER, PDIP8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L6470HTR-CUT TAPE | 制造商:ST 功能描述:L6470H Series 45 V Quad Output dSPIN Microstepping Motor Driver - HTSSOP-28 |
| L6470PD | 功能描述:馬達/運動/點火控制器和驅動器 dSPIN 7.0A 8 - 45 V DMOS Motor Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L6470PDTR | 功能描述:馬達/運動/點火控制器和驅動器 dSPIN 7.0A 8 - 45 V DMOS Motor Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L64710GC-30 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Encoder/Decoder |
| L64710GC-40 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Encoder/Decoder |
發布緊急采購，3分鐘左右您將得到回復。